background image

© 2018 Kymeta Corporation.

8

07 February 2018

KyWay™ Terminal Quick Start Guide

13 CE declaration of conformity

This equipment conforms with the essential requirements and other relevant provisions of Radio Equipment Directive

(2014/53/EU).

14 FCC notifications

This device complies with Part 15B of the FCC rules. Operation is subject to the following conditions:

1.

This device may not cause harmful interference.

2.

This device must accept any interference received, including interference that may cause undesired operation.

This product complies with the requirements set forth in CFR 47 Section 1.1307 addressing RF Exposure from radio

frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency

Electromagnetic Fields.

This product complies with EN 50835 for RF exposure.

The product is a transmit and receive satellite terminal; the user must comply with all applicable local, national, and

international laws and regulations regarding the installation and use of this product.

15 Legal disclaimer

© 2018 Kymeta Corporation. KYMETA, CONNECTED BY KYMETA, MTENNA, KYWAY, KĀLO image, and KĀLO are trademarks of Kymeta

Corporation, with registrations or applications for these marks pending in Brazil, the European Union, Japan, Norway, Singapore, South

Korea, and the United States.

16 Contact information

12277 134th Ct NE, Redmond, WA 98052, USA | +1 (425) 896-3700 www.kymetacorp.com

twitter.com/KymetaCorp | facebook.com/kymetacorp | instagram.com/kymeta | linkedin.com/company/kymeta-

corporation

17 Revision history

Revision

Change

Date

A

Initial document.

7 February 2018

Summary of Contents for KyWay U7 8W











Reviews: