background image

1 / 4

A

R or S 

(2x)

A

A

B

B

B

(2x)

(2x)

D

Longer screws 
install closest to 
the door jamb.

door frame

Traditional

Contemporary

A

B

63983 / 02
Z-Wave

Signature Series Deadbolt 

with Home Connect

Installation and User Guide

Kwikset

1-866-863-6584

www.kwikset.com

Parts in the box

Latch

“B” is not included. If needed, 

please contact Kwikset to order 

a drive-in latch for your lock.

Interior Assembly

Mounting 
Plate

Fasteners

Exterior Assembly

If drilling a new door, use the supplied template and the complete 
door drilling instructions available at www.kwikset.com/doorprep.

Note: Additional door preparation may be 
required for doors with 1-1/2" (38 mm) holes. 
Consult the deadbolt drilling instructions at 
www.kwikset.com/doorprep.

*Service kits for 2-1/4" (57 mm) thick doors 
are available through Kwikset.

or

backset

Measure to confirm that the hole in 
the door is either 2-1/8" (54 mm) or 
1-1/2" (38 mm).

Measure to confirm that the backset is 
either 2-3/8" or 2-3/4" (60 or 70 mm).

2-3/8" or 2-3/4"

60 or 70 mm

1-3/8" – 1-3/4"*

35 – 44 mm*

Measure to confirm that the hole in 
the door edge is 1" (25 mm).

Measure to confirm that the door is 
between 1-3/8" and 1-3/4"* (35 mm 
and 44 mm*) thick.

A

A

B

C

D

E

B

C

D

Is the door edge chiseled?

Are the latch holes centered in the door hole?

Which latch are you installing?

Install strike on the door frame.

 Make sure the hole in the door frame is drilled a 

minimum of 1" (25 mm) deep.

Hold the latch in front of the door hole, with the latch 
face flush against the door edge.

2-1/8"

54 mm

1-1/2"

38 mm

1"

25 mm

YES

YES

NO

NO

Use latch “A”. If the 
latch bolt is not already 
extended, extend the 
latch bolt as shown.

No adjustment is required. 
Proceed to next step.

Rotate latch face as 
shown to extend latch.

wood 
block

Use latch “B” (not 
included). If the latch 
bolt is not already 
extended, extend the 
latch bolt as shown.

Latch “A”

Latch “B”

ENGL

IS

H

Required tools

Ruler

4 AA Batteries

Hammer

Wood block

Phillips head screwdriver

Additional Tools (depending on application)

Strike

Cylinder

D

R

T

U

V

W

X

S

Keys

SmartKey  
tool

K

C

J

 A

 B

E

F

F

G

G

H

H

M

L

N

P

Q

Traditional

Contemporary

or

chiseled

not 
chiseled

or

or

1

Prepare the door and check dimensions

2

Install the latch and strike

Summary of Contents for 910CNT ZB 11P SMT

Page 1: ... mm 1 3 8 1 3 4 35 44 mm Measure to confirm that the hole in the door edge is 1 25 mm Measure to confirm that the door is between 1 3 8 and 1 3 4 35 mm and 44 mm thick A A B C D E B C D Is the door edge chiseled Are the latch holes centered in the door hole Which latch are you installing Install strike on the door frame Make sure the hole in the door frame is drilled a minimum of 1 25 mm deep Hold...

Page 2: ...iring is unsuccessful follow your system s instructions to remove the lock from any other network then press button A on the lock one time Repeat steps 4D and 4E If still unsuccessful consult the Programming and Troubleshooting Guide on the Deadbolt with Home Connect page at www kwikset com wirelesslocks G Hold the interior assembly a maximum of 12 305 mm from your smart home controller When promp...

Page 3: ...ton The Status LED will flash red and green and the lock will beep Press and release the Program button again The latch bolt will retract and extend on its own Did the latch bolt retract and extend on its own YES NO turnpiece shaft torque blade H U 2x a b Press and hold Hold 3 5 seconds Release button Press and release Re key the lock if needed Install the battery cover A B IMPORTANT Remove batter...

Page 4: ...y based on building construction and communication path with 35 feet being typical installed distance from smart home controller It may be necessary to install additional Z Wave beaming capable devices that can serve as repeaters to enhance the communication path between the lock and controller for a more robust Z Wave network Deadbolt Interior at a Glance Reference Guide Back panel Program button...

Reviews: