manualshive.com logo in svg

KVH Industries TracVision UHD7, Installation Manual, Page: 16 / 41

Share
Download
KVH Industries TracVision UHD7 Installation Manual Download Page 16

14

Follow these steps to connect the antenna cables to 
the belowdecks equipment. 

a.

Connect a grounding block in-line with each

RF cable from the antenna (see Figure 23 and

“Grounding Requirements” on page 21

).

b.

Connect the RF1 cable from the antenna to the

“Antenna” jack

 

on the TV-Hub (see Figure 23).

c.

Hand-tighten the RF cable until it is all the way

into the “Antenna” jack. Then tighten it with a

7/16" torque wrench set to 15 in.-lbs.

d.

Connect the RF2 cable from the antenna to the

“Power to SWM” connector on the SWM

power inserter (see Figure 23).

e.

Using fasteners appropriate for the mounting

surface, secure the power inserter to the

mounting surface.

NOTE: 

Do not connect the SWM power inserter’s AC 

power cable to vessel power at this time. Power will be 

connected in 

“Connect Power” on page 21

.

Figure 23:  TV-Hub Antenna Connection

POWER

TO SWM

AC Power

SWM Power

Inserter

Antenna

Deck

TV-Hub

Antenna

Grounding

Block

RF1

RF2

Do not connect anything other than the 
antenna’s RF1 cable to the “Antenna” jack. 
The TV-Hub supplies voltage that will 
damage other devices, such as multiswitches, 
receivers, DVRs, etc.

IMPORTANT!

Wire the TV-Hub

11

Summary of Contents for TracVision UHD7










































Reviews:

No comments