manualshive.com logo in svg

KVH Industries TracPhone V11IP, Installation Manual, Page: 17 / 55

Share
Download
KVH Industries TracPhone V11IP Installation Manual Download Page 17

16

Follow these steps to connect the antenna cables.

Remove the Cable Cover

To access the antenna’s connectors, you first need 
to detach the cable cover. Loosen the six #6-32 
captive screws securing the cable cover to the 
base (see Figure 22). Then set the cable cover 
aside in a safe place.

Attach the Second Foam Seal, If Needed

If you routed the cables through a hole directly 
underneath the antenna (see “Cut Out the Cable 
Access Hole, If Needed” on page 10), follow 
these steps to attach the second foam seal to the 
base of the antenna.

a.

Clean and dry the bottom of the antenna.

b.

Peel off the paper backing from the second 

foam seal to expose the adhesive. Align the 

foam seal so it is centered on the antenna (see 

Figure 23). Then press the foam seal firmly 

onto the underside of the antenna.

#6-32 Captive

Screw and 

Washer (x6)

Cable
Cover

Figure 22:  Cable Cover

Foam Seal

(if necessary)

Figure 23:  Foam Seal on Base of Antenna

Wire the Antenna

9

Summary of Contents for TracPhone V11IP
























































Reviews:

No comments