manualshive.com logo in svg

KVH Industries TracPhone V11IP, Installation Manual, Page: 37 / 55

Share
Download
KVH Industries TracPhone V11IP Installation Manual Download Page 37

36

Static IP Configuration 

In a static IP configuration, a network device is 
assigned an IP address that can be accessed 
directly from the Internet. It does not receive an 
IP address from the ICM. Follow these additional 
steps to configure the network. 

a.

Ask the customer to fill out the request form 

at 

www.kvh.com/staticip

. In addition, the 

system must be activated for mini-VSAT 

Broadband service, and it must remain online 

until KVH configures the system over the air.

b.

Connect the static IP device to “User 

Ethernet” port 4 on the ICM.

c.

The customer will need to configure the 

device’s TCP/IP properties according to the 

instructions KVH will provide in an email 

upon fulfilling the static IP request.

d.

Connect all other (non-static IP) computers 

and/or network devices to “User Ethernet” 

ports 1-3 and Wi-Fi, as required. These ports 

and the built-in WAP provide direct Internet 

access without a user login. Follow the steps 

in “Standard Configuration” on page 35. 

Figure 69:  Static IP Configuration

User Ethernet

Bridge PC

DHCP

Engine Room PC

Officers PC

192.168.5.100

192.168.5.101

192.168.72.100

LAN

: 192.168.5.1

WAN

: 192.168.72.99

Static

Firewall

ICM

1 2 3 4

Figure 70:  Static IP Configuration Wiring Example

A static IP address should only be assigned to 

a secure device, such as a firewall router.

IMPORTANT!

Continued 

Configure the Network

20

Summary of Contents for TracPhone V11IP
























































Reviews:

No comments