8/02
5
2.0 New equipment - be careful!
It is very important to be careful when new equipment is going to be used for the first time.
Incorrect mounting of equipment and operational errors can lead to expensive repair work and
operational losses. The
Kverneland
factory warranty is not valid if the instructions in this
operating manual are not followed correctly.
Please ensure that all equipment is mounted correctly and that it is not damaged. Also, check that
the hydraulic hoses are mounted such that they are long enough for free hydraulic cylinder
movement and that they do not become trapped during implement operation.
When leaving the
Kverneland
factory all new equipment is lubricated with the correct kind of
grease. Only use quality grease recommended.
Check that all nuts and bolts are firmly tightened (look at chapter 21.0 Tightening torque), this is
very important after the first hours in use.
Important Safety Recommendations
All mounted reversible ploughs:
On large fully mounted reversible ploughs it is recommended to replace the cross shaft after
approx. 1000 km of transport operation. This is for safety reasons in the unlikely event a failure
should occur.
Hydraulic system:
The hydraulic system is working under high pressure and is therefore potentially dangerous. It is
very important that all hoses and connections are checked frequently for leakage and external
damage.
The hydraulic hoses should not be connected to, or removed from the hydraulic system on the
tractor unless the oil pressure in both the tractor and implement has been released.
In accordance with the EU-directive, all hydraulic hoses should be exchanged with new genuine
Kverneland replacements after 6 years. Porous and defective hoses must always be replaced
immediately.
Oil leakage from damaged hoses and connections can cause fatal injury and possible fire
risk.
Always seek medical treatment immediately following an injury.
Note:
The sound level on all ploughs is less than 70 dB.
Summary of Contents for PL-100
