8/02
19
10.0 Disc coulter
10.1 Disc coulter for auto-reset beam
Disc coulters can be mounted on all furrows on ploughs fitted with the auto-reset beam.
The disc coulter for the auto-reset beam can be delivered in two variants. The most common type
is shown in fig. 12 to fig. 14. Adjust the depth by loosening bolt (T) (fig. 13). The limit stop for the
turning angle for the disc is also adjusted by loosening the bolt (T). Care must be taken when
adjusting the rear disc coulter so that it does not collide with the rear depth wheel.
The disc coulter is adjusted so that 1/3 of the diameter (D) cuts into the ground. this will ensure
positive rotation and avoid the disc from stopping. The distance between the coulter and the share
should be minimum of 5cm. When working in stony soil, the distance should be increased.
The distance between the coulter and the landside can be adjusted by loosening both bolts (U) and
turning the eccentric (X). The distance should be 1 - 4 cm (fig. 14).
Disc coulter with parallel side adjustment is shown i fig. 16. To adjust the working depth, bolt (A)
(fig. 16) is loosened and the arm (B) is raised up or down against the serrated boss mounted to the
arm (C). The distance between the coulter and the landside can be adjusted by loosening bolt (U).
The cranked arm (C) is then moved to the appropriate working position and bolt (U) tightened. The
disc distance should be 1 - 4 cm (fig. 14).
10.2 Disc coulter for shearbolt beam
Disc coulter for fixed beam is shown in fig. 15.
The disc coulter can only be mounted on the rear body assembly.
The disc coulter is adjusted so that 1/3 of the diameter cuts into the ground. The limit stop for the
turning angle for the disc is also adjusted by loosening the bolt (T). The distance between the
coulter and the share should be minimum 5cm. When working in stony soil, the distance should
be increased.
Adjust the depth by loosening bolt (A) (fig. 15) and adjust the disc to the correct working position.
When shallow ploughing, it is possible to adjust the disc's depth by lowering the shaft (B) (fig. 15).
The distance between the disc coulter and the landside can be adjusted by loosening both bolts (U,
fig. 15) and turning the excentric (X). The distance should be 1 - 4 cm (fig. 14).
NB! Remember to tighten all the bolts frequently.
Summary of Contents for PL-100
