8/02
15
9.0 Beams
9.1 Auto reset system
Fig. 5 shows the HD-spring. For heavy soils two additional leaves No. 5 can be supplied (fig. 5). The
standard spring is with two leaves No. 5. For heavy soils, it is possible to mount two spring units on
top of each other.
To disassemble a complete beam with body and skim equipment:
-
Ensure that the beam is sitting against the balls and is supported by lifting equipment or by
parking the plough on a level floor.
-
Release the spring tension by loosen the bolts (E) and (F) (fig. 6).
The spring suspension rod (H) (fig. 7) is pushed forward allowing the bolt (A) (fig. 8) to be pulled
out. The beam is now dismounted from the plough and can be removed.
Assemble in reverse order.
The spring is tightened by means of the two bolts (E) and (F). Screw in the bolt (E) halfway. Then
turn bolt (F) so that the clearance (I) between the drawbar and the inner side of the leg section is
1 - 2 mm (fig. 7). Finally bolt (E) (fig. 6) is adjusted until the distance between (J) and (K) is 70 cm
(fig. 9). This dimension is marked on the side of the long spanner (fig. 10).
With correct adjustment, maximum spring tension is achieved. Always use the correct number of
leaves to suit soil type. Too many leaves fitted will prevent the auto-reset system to operate
correctly.
Over time, the spring will become out of adjustment and must then be re-set again in accordance
NB!
Always maintain the setting as per the decal (70-cm). If ignored, the spring system may not
function correctly and will result in the assembly flexing the wrong way (fig. 9, decal).
Summary of Contents for PL-100
