8/02
13
7.0 Tractor
7.1 Tractor equipment
The tractor must be equipped with (minimum) :
-
One double acting hydraulic outlet for the turnover cylinders
-
One double acting hydraulic outlet for the wheel carriage. If the plough is equipped with a
joystick or foot pedal the following operations can be made-
a)
Raise and lower the centre carriage section,
b) Raise and lower the rear ploughing section,
c) Adjust the Vari-Width furrow width system
-
Optional equipment can be delivered:
-
One double acting hydraulic outlet for the hydraulic furrow width adjustment
-
One double acting hydraulic outlet for Vari-Width system if a joystick/foot pedal control is not
used
-
One double acting hydraulic outlet for the hinge cylinder if a joystick/foot pedal control is not
used
-
If the plough is equipped with a Packomat, additional outlets may be required.
NB!
The tractor lower link arms (A, fig. 4) must be stabilised preventing sideways movement. If
this is not possible, the free movement has to be limited and equal on both sides.
Front-end tractor weights are usually required. For "in-furrow" operation, the rear tractor wheel
setting (between inside faces of tyres) should be from 110 to 160 cm. When using a 4WD-tractor it
is most important that wheel distance in front is not less than that of the rear wheel setting. If the
distance in front is less than the rear, there will be a width variation on the first furrow. However,
when using a 2WD-drive tractor it can be an advantage to adjust the front wheels 0 to 10 cm. wider
for optimum ploughing performance (fig. 2).
When part of the tractor tyre rolls on the land with a distance (E) or when using a furrow opener
(fig. 3) the rear wheel distance (D) would be A + 2E.
NB!
When using furrow openers, the width
of the front furrow (E) will be narrower than the remaining furrows. The front furrow width should
always be set from the original furrow wall.
The tractors' lift rods should be equal in length and the angle of the lower draft arms equal on both
sides. The air pressure must also be equal on both rear wheels.
7.2 Tractor attachment
The cross shaft is delivered with Cat. III (Ø36 mm) 965 mm.
The parking stands must be raised before ploughing and put down again when parking the plough.
Summary of Contents for PL-100
