Kverneland CTC 420 Service Manual Download | Manualshive

Page: 30 / 45

background image

30

5.12

Double disc gang

X

°

X

°

The method to set the angle of the double disc gang is the same than for the
combi disc

The working angle on double disc gang can be adjusted depending on
the type of soil.
The angle should be set the same for both gangs (see drawing). In this
way, the front gang is not more loaded than the rear.

5. Adjustments

«
...
28
29
30
31
32
...
»

Summary of Contents for CTC 420














































Reviews:

No comments

Related manuals for CTC 420

Brand: Panasonic Pages: 9

Brand: JB Systems Pages: 7

Brand: 3B SCIENTIFIC PHYSICS Pages: 36

Brand: 3A HEALTH CARE Pages: 16

Short/cut 2000 Audio Editor

Brand: 360 Systems Pages: 4

Brand: ParaBody Pages: 5

Brand: Baileigh Industrial Pages: 28

Brand: Baileigh Industrial Pages: 56

Brand: KaVo Pages: 49

Brand: Easson Pages: 33

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 64

Brand: M-Audio Pages: 16

Brand: M-Audio Pages: 4

Brand: M-Audio Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands