Kval Commander III Operation Manual Download Page 125

Page: 125 / 168

About the Calibration Screens

KVAL Commander III Operation Manual

4-10

About the Calibration Screens

At this screen, adjustments are designed to fine tune the servos for optimum accuracy.

Summary of Calibrations

The Calibrations available are listed in the table below.

Calibrations

Description

Hinge Heads (All Over)

Calibrate the X, Y or Z axis of the Hinge head and its too

see “Hinge

Head (Over All)” on page 4-12

Hinge Tools

Calibrate each tool separately in the X, Y or Z axis

see “Hinge Tools”

on page 4-13

Hinge Carriage Location

Calibrate the X axis location across the front section.

see “Hinge Car-

riage Location” on page 4-15

Lock Head

Calibrate the X axis location across the Lock Head on the back sec-
tion of the machine. (Option: Thickness encoder calibration is also
locat4ed in this section)

see “Lock Head” on page 4-16

Door Stops

Calibrate the X axis location of the in-feed and out feed stops

see

“Door Stops” on page 4-20

Fast Lock Timing

Adjust the time of deployment lock router.

see “Fast and Slow Lock

Plate Timing” on page 4-21

Summary of Contents for Commander III









































































































































































Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands

Kval Commander III, Operation Manual

Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands