Kval Commander III Operation Manual Download Page 136

Page: 136 / 168

About the Calibration Screens

4-21

KVAL Commander III Operation Manual

Fast and Slow Lock Plate Timing

Fast Lock Timing:

Under

normal

operating (No Extend Time), the routing time can be adjusted to

match the flow controls on the machine. Before adjusting these times, make sure the flow controls
are set properly.:

Slow Plate Routine

The router time can be adjusted to match the flow control that is mounted on

the valve for slow sequence. Before adjusting the time, make sure the Fast Plate Routine is set
properly before adjusting times and flow controls in this section.

X -

X +

X -

X +

The

In-Feed

Stop is the

reference for the top of
a right hand door.

The

Out-Feed

Stop is

the reference for the
top of a left hand door.

View is from the rear of the machine

Summary of Contents for Commander III









































































































































































Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands

Kval Commander III, Operation Manual

Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands