Kval 990-F4 Service Manual Download

Page: 90 / 118

Troubleshooting Basics

KVAL 990-F4 Service Manual

4-8

FIGURE 14.

Troubleshooting Flow Chart

Analyze the Sub Systems

Check the

Load

for mechanical issues

• Is the Load “bound up?
• Is there sufficient lubrication?
• Is it an alignment issue?
• Is anything damaged?

Check the

Position Feed Back

Determine What:

What Subsystem is Respon

sible for the Failed Sequence

Step.

Analyze

the subsystem:

Check the

Load

Check the

Position Feed Back

Check the

Positioning System

See

“Analyze the Sub Systems” on

page 4-8

TABLE 4-1.

Typical KVAL Machine Sequence

Typical Machine Sequence

Responsible Subsystem

1. Move Door into Position

Feed System

2. Clamp the Door

Door Clamp

3. Make the Cuts

Cutter Positioning

Cutter Power

4. Unclamp the Door

Door Clamp

5. Move Door Out

Feed System

6. Wait for Next Door

Feed System

Basic Troubleshooting Steps

Determine Where:

The Sequence Step

Where

the Failure Occurs

What was the Machine Trying to Do?
What Was the Machine Trying to Do Next?

Check the Sequences in the Table Below.

How is the Broken Section Suppose to Work?

What is Keeping the Broken Section From

Working?

What Part of the Machine is not Working?

Check the Subsystems in the Table Below.

Ask

Narrow

Verify

Summary of Contents for 990-F4























































































































Search results

Summary of Contents for 990-F4

Reviews:

Related manuals for 990-F4

Brands by name

Popular brands

Kval 990-F4, Service Manual

Search results

Summary of Contents for 990-F4

Reviews:

Related manuals for 990-F4

Brands by name

Popular brands