27
26
HOW TO USE THE LID OPENER
Use the lid opener when the lid doesn't open normally after juicing.
Hold the feed chute steady and turn the lid opener counterclockwise.
12
Be sure that the top-set is on the main body before using the lid opener.
Position the lid opener horizontally and connect the hooks as shown in the illustration.
11
CAUTION
TROUBLESHOOTING Q&A
When there is no power to the juicer:
· Check if the power cord is properly plugged in.
· Check if the drum lid and the juicing bowl are
properly assembled.
· Check if the top-set and the base are properly assembled.
·
Juicer will not operate if parts are not assembled properly.
Low juice yield:
· Different ingredients hold different amounts of liquid
that will yield different amounts of juice.
· If the ingredients are not fresh, they may contain reduced
amounts of liquid which will yield less juice.
Soak ingredients in cold water for about 30 min prior to
juicing for the best results.
· If the ingredient itself has low water content, it may
help to soak it in water before juicing.
· If juicing ingredients with small seeds, after a few
servings the juice yield may be reduced.
For best results, disassemble and wash the top-set in
between juice sessions.
·
If there is seed residue on the bottom of the
strainer, this can affect juicer performance and
the overall juice yield.
There is too much pulp in the juice:
· To reduce the fine pulp, clean the top-set frequently
and remove the pulp.
· If the strainer and the screw are damaged and affecting
the juicer’s performance, it is recommended the parts
be replaced.
* The lifetime of each part may vary depending on length
and method of use and ingredients extracted.
The drum lid will not close:
· Make sure the juicing screw is pushed all the way into
the strainer in order for the drum lid to close properly.
·
If the juicing screw is not properly in position, the drum
lid may not close.
Odd noise from the juicer:
· Check if the parts are assembled correctly.
Try reassembling the parts and listen for the odd noise.
· Do not start the juicer unless there are ingredients and
or liquid in it.
·
Operating the juicer without ingredients can cause
damage to the screw.
· If the juicer is operated without ingredients or liquid,
the noise level can increase and can also lead to damage.
· The friction noise from the juicing screw and the strainer
will disappear when ingredients are inserted into the juicer.
· If the noise occurs when ingredients are inserted into
the juicer, check the size of the ingredients.
Do not insert anything over 1.5 inches in thickness.
· Depending on the type of ingredients, the dimensions
can be smaller.
·
The noise can occur if the juicer is operated on an
uneven or slanted surface. Place the juicer on a
horizontally flat surface when operating.
The extracted pulp is very moist:
· During the very beginning of extraction, the pulp can
be more moist temporarily.
· Pulp can be affected by the ingredient's condition.
When the ingredient is not fresh, the juice often sticks
to the pulp.
During operation, the juicing bowl shakes:
· The juicing screw and the strainer are set up to crush
and squeeze the ingredients. It is normal for the juicing
screw and the strainer to vibrate.
· If the ingredient is very fibrous, the vibration from the
top-set may be stronger.
During juicing, the juicer stopped:
· Check the power cord and make sure it is plugged in
correctly.
· Check that all the parts are correctly assembled.
· If too many ingredients are inserted at one time,
this can cause the juicer to stop.
· When the juicer stops because there are too many
ingredients inserted in it, press the REVERSE - OFF -
FORWARD button in this order, switching back and
forth 2 to 3 times.
·
The reverse setting will push the ingredients up,
and the forward setting will pull the ingredients down.
· After using for more than 30 minutes, the juicer may
stop due to overload protection. Let the juicer cool for
30 minutes to 1 hour before juicing again.
· If there are hard seeds within the ingredients, remove
them before juicing. Hard seeds can damage the juicer.
Layers of separation in the juice:
· Depending on the density of the ingredients,
the extracted juice may show layers of different juices.
It is different from separation due to oxidation
caused by juicing with a high-speed juicer.
The drum lid is stuck:
· After juicing, let the juicer operate for another
30 seconds to extract the remaining pulp.
· If there is too much pulp in the top-set, this can cause
the drum lid to not open. In this situation, press
EN
EN
