background image

17

16

How to Disassemble and Clean

Note

Place the juicing bowl underneath the running 
water and unplug the compression silicone to 
clean the pulp spout.

Soak the juicing bowl in a solution of warm water with baking 
soda or little bit of bleach to clean the excess build up.

Tip

It is not necessary to completely clean the juicer in 
between making multiple juices.  When fi nished with 
juicing, disassemble and clean thoroughly.

Tip

Clean the base with soft damp towel and dry.

Remove the juicing screw, stainer and rotation 
wiper unit from the juicing bowl. Clean with 
provided brush.

Note

Tip

Note

Underneath the running water, clean the out 
side of the juicing screw with a dish scrub.  Use 
the end tip of the cleaning brush to push out 
any residue within the crevices on bottom of the 
juicing screw.

With the smart cap closed, fi ll the juicing bowl 
with water and turn on the juicer. 

After a moment, open the Smart Cap and let 
the water run out of the juicing bowl.

* The products illustrated/photographed in this booklet may vary slightly from the actual product. 

Note

If the towel is very wet, make sure to squeeze out the 
access liquid before using it on the juicer.

After juicing ingredients with seeds, make sure to 
thoroughly clean the bottom crevice of the juicing 
screw.  If this area isn’t properly cleaned, this can aff ect 
the balance between the juicing screw and the strainer 
and damage the parts. 

ㆍ 

Extract all the remaing pulp in the juicing bowl 
before stopping the juicer.

ㆍ 

For easier clean up, operate the juicer for additional 
30 seconds after juice has been extracted.

When the drum lid is stuck, press the REVERSE - OFF 
- FORWARD button in the order, switching back and 
forth 2~3 times to dislodge. Then place your hands 
on top of the drum lid and fi rmly press down as you 
simultaneously turn the drum lid counter clockwise 
to open.

Please thoroughly clean the juicing screw under 
running water with the cleaning brush.

Completely dry before using ensuring that the juicing 
screw is clean without any residue.  

ㆍ 

Immediately clean the juicer after each use. If remaining 
residue in the juicer dries up, it can make disassembling 
diffi

  cult as well as clean-up. The excess build up can 

cause poor performance in future uses.

 

ㆍ 

For easier disassembling, place the top-set in the sink 
and run the water down from the top of the top-set.

ㆍ 

Thoroughly dry the bottom of the juicing screw where it 
connects to the metal cylinder shaft on the base.

Switch OFF and unplug the power cord from the 
wall outlet.

Rinsing

11

4

6

7

5

1

2

Turn the drum lid counter clockwise to open.

2

Note

ㆍ 

When moving the appliance, do not lift by grabbing 
the feeding tube. Always lift the appliance by 
grabbing the base or handle. 

Turn the top-set counter clockwise and lift off  
the base.

3

Summary of Contents for M1













Reviews: