Kuvings CB-1000, User Manual, Page: 7 / 32

12 13
COMMERCIAL AUTO VACUUM BLENDER COMMERCIAL AUTO VACUUM BLENDER
READY
COVER OPEN
WELCOME
KUVINGS
WELCOME
KUVINGS
Fasten the Sound Enclosure to the Body.
- Check if the vacuum module is properly connected to the
Sound Enclosure.
- Check that the Sound Enclosure is properly
inserted into the cushion pad.
* If the Sound Enclosure is not properly fastened,
the ‘Automatic open/close’ and ‘vacuum’ functions may not work.
Put the ingredients into the container and close
the container lid.
- Cut the ingredients into 3cm or less and put it in less than the
maximum capacity.
- Check if the lid is properly fastened to the container.
When the operation is complete, turn off the
power and disconnect the power plug.
- Blending stops by pressing the ‘Start/Stop’ button or
pressing the ‘Control panel button’.
When the power is connected, it will be in power standby
mode.
- Display: When the program loading is completed, READY is
displayed on the screen.
- Control panel: The white LED of the control panel button
blinks once.
Select the control panel button to operate the product.
- When you select a button on the control panel, the button's
LED lights up in white and blending operate.
- Press the ‘Auto Vacuum’ button to turn on the white LED and
activate the ‘Vacuum Mode’.
- When you press the ‘Auto open / close' button, the white
LED lights up and the ‘Auto open / close’ mode is activated
after vacuum.
READY
COVER OPEN
WELCOME
KUVINGS
WELCOME
KUVINGS
READY
COVER OPEN
WELCOME
KUVINGS
WELCOME
KUVINGS
READY
COVER OPEN
WELCOME
KUVINGS
WELCOME
KUVINGS
1
2
3
4
5
2
Container Set
1
Sound Enclosure / Body
- Clean the Sound Enclosure and Body with dry cloth.
* Putting Sound Enclosure & Body in water
may cause failure; this can be repaired by paid service.
(1) General Cleaning & Care
①
Pour 400ml of water and one or two drops of neutral detergent
in the container and blend at 70% speed for 20~30 seconds.
②
When blending is complete, remove the residue with a soft cloth or
sponge Then rinse it throughly with clean water.
(2) Thorough cleaning (in case of severe calcareous
contamination inside the blade or container)
①
Pour 50g of citric acid in a container based on 1L of hot water
(140
℉
), dissolve it completely, Then soak it for at least 3 hours.
②
After soaking, blend at 70% speed for 20~30 seconds to remove scale.
③ When blending is complete, discard the water inside of the container, remove
the residue with a soft cloth or sponge, and rinse thoroughly with clear water.
(3) Attention (For paid service)
①
If the outer bottom surface (coupling) is immersed in water when washing the container,
malfunction and It may cause rust.
②
Do not wash the container set into the dishwasher.
③
Blade set will rotate if detergent remains or immersed in water.
It may cause corrosion (wear phenomenon) of parts.
How to Use Cleaning and Care
* After purchasing the product, clean the container set (container lid, Container Lid Packing,
container and blade set) with dishwashing detergent before use.
* When used for the first time, a small amount of smoke and odor may be generated from the body.
* Parts made of rubber must be wiped with a wet tissue (wet cloth) or washed in cold running water,
and then dried sufficiently. (If you wash with hot water or a dishwasher, it may cause damage to
function due to deformation.)
Washing may take longer if the water temperature is low. A rough scrubber may scratch
the inner side of the container. Be sure to clean with a soft cloth or soft sponge.
Tip
EN