background image

INTRODUCTION

    The AUTO CHARGE 2000 is a compact, completely automatic, dual channel
battery charger designed for vehicles with two batteries.  The charger is rugge-
dized to withstand the shock and vibration encountered by vehicle mounted
equipment. The Auto Charge 2000 Pump Plus operates an 091-9 air compressor. With the
selector switch in the AC position the compressor runs only when the AC power is applied.
With the selector switch in the DC position the compressor will operate when the AC power
is on or off. In either position the compressor operates from the vehicle’s batteries, the Pump

Plus automatically recharging the batteries as required.

The battery charger features:

• Independent charge controls for each battery

• Electronic remote sensing of true battery voltages, eliminates the need

   for sensing wires

• Automatic current limiting and apportionment

• Built-in BATTERY SAVER

• Remote dual battery charge/condition indicator

• Power “ON” LED indicator

• BATTERY SAVER overload indicator

DESCRIPTION

Independent Charge Controls & Electronic Remote Sensing

     The charger contains two independent charge controls, one for each battery.

This allows each battery to be independently charged while maintaining battery

isolation.  Each battery voltage is remotely sensed, electronically, eliminating the

need for four sense wires.  Each of the charge controls is completely automatic and

stops charging the battery when it is fully charged.  There is no trickle charge and

therefore no danger of overcharging and water boil-off.

Automatic Current Limiting & Apportionment

     The charger contains automatic current limiting at 15 amperes.  This is a total

current limit for the two batteries combined.  The charger automatically apportions

the current to each battery.  Either battery can draw the total 15 amperes.  When

charging unequally charged batteries, the lower charged battery receives a higher

charge rate.  When the batteries are equal, the current is shared equally until they

are fully charged at which time the current goes to zero.

Summary of Contents for 091-9-2000









Reviews: