background image

“KUSAM-MECO”

AN ISO 9001:2015 COMPANY

“KUSAM-MECO”

AN ISO 9001:2015 COMPANY

 

21

+Hz

+ACmV

ACmV   ,  Hz 

 functions

Press  the  SELECT

  button  momentarily  to  select  the  subject

functions in sequence.  Last selection will be saved as power up 

default for repeat measurement convenience.

+ACmV

+ACmV

DCmV, DCmV 

, DC+ACmV 

, Logic-Level     Hz 

& Duty%

Press  the 

SELECT

  button  momentarily  to  select  the  subject 

functions in sequence.   Last selection will be saved as power up 
default for repeat measurement convenience.

22

CAUTION

Using  resistance  and  continuity  function  in  a  live  circuit  will 
produce  false  results  &  may  damage  the  instrument.    In  many 
cases the suspected component must be disconnected from the 
circuit to obtain an accurate reading.

nS Conductance, 

W

 Resistance,      Continuity functions

Press  the 

SELECT

  button  momentarily  to  select  the  subject 

functions in sequence.   Last selection will be saved as power up 
default for repeat measurement convenience. 

Conductance (unit-Siemens) is the inverse of  Resistance,  that  is  
S=1/

or nS=1/G

W

. It virtually extends the Resistance measure-

ments to the order of Giga-Ohms for leakage  measurements.

Note :

      Continuity   function   is   convenient  for   checking   wiring 
connections and operation of switches.  A continuous beep tone 
indicates a complete wire.

 

Summary of Contents for KM 525






















Reviews: