“KUSAM-MECO”
AN ISO 9001:2008 COMPANY
“KUSAM-MECO”
AN ISO 9001:2008 COMPANY
07
06
2. Button “°C/°F/°K”
Press the °C/°F/°K button to cycle through temperature scale,
°C, °F and °K.
3. Type Selection (thermocouples)
Press the “type” button and the selected symbol will blink which
means in the setting mode.
Press “
}
” button to make right shifts to cycle through
K
g
J
g
T
g
E
g
R
g
S
g
N
g
L
g
U
g
B
g
C
g
mV.
Press “
|
” button to make left shifts to cycle through
K
g
mV
g
C
g
B
g
U
g
L
g
N
g
S
g
R
g
E
g
T
g
J
Press the “type” button again to choose the selected thermocouple.
4. Backlight “ ” button
Pressing the button less than two seconds to turn on and pressing
the button again less than two seconds to turn off the backlight in
the LCD. It will turn off after thirty minutes without operation.
Auto Power Off
It is in the APO mode when the meter is turned on and will turn off
the meter without operation for fifteen minutes. Pressing the “ ”
button over two seconds to cancel the function. And pressing the
“ ” button again to activate the APO function.
5. “ REL” button
The relative value function can be used for comparing the saved
reference value with other measurements. Press the “ REL” button
less than to store the current measurement as the reference value,
and press the “ REL” over two seconds to disable the function.
6. “ HOLD” button
When HOLD mode is selected, the thermometer holds the present
readings and stops all further measurements. To activate the data
hold mode, press the HOLD button, and “HOLD” is displayed on the
LCD. Pressing the HOLD button again cancels the function, & the
instrument will automatically resume measurements. When the
Hold key is activated, it will stop functions of the other entire key
except Power & Backlight.
7. “ T1/T2 SOURCE” button
Pressing T1/T2 SOURCE to cycle through T1, T2 and SOURCE. In
the main display the blinking digit is the one to be adjusted, you can
push the “
|
}
” button to make right or left shifts to the desired
position. When incrementing to the utmost range of the selected
thermocouples, the LIMIT will show on the display.
SOURCE is to provide the output parameter settings. There are ten
individual temperature setting points in group 0, which can be set at
your desired output point. Use “
|
}
” to shift the desired digit to be
adjusted and rotate the knob to increase or decrease the values you
want to set. Press the T/C OFFSET to save the settings.
8. “ OFFSET” button (Thermocouple offset adjust)
When the main display input is T1 or T2, and socket thermocouple is
connected. Press T/C OFFSET over two seconds the SET
annouciator will appear on the right side of display and enter the
offset adjustment mode. And the blinking digit is the one to be
adjusted. Rotate the knob to the right increasing the values, to the
left side decreasing the values. The maximum range of the knob is
±5 centigrade. When turning to the utmost range, it will appear
LIMIT symbol on the left side of the display and means that there is
no further incrementing of the offset. Press the T/C OFFSET over
two seconds to save the settings.
9. “ MIN / MAX ” button
Press MIN / MAX button to enter the MIN/MAX recording mode and
REC shows on the display. The beeper emits a tone when a new
minimum or maximum measurement is recorded. Press the MIN /
MAX button again to rotate through the current readings :
MAX : The highest measurement recorded.
MIN : The lowest measurement recorded.
MAX-MIN : The difference of the highest and the lowest
measurement.
AVG. : The average values of the measurements.
Press MIN/MAX button over two seconds to exit the function.