background image

01

02

1. SAFETY PRECAUTIONS :

Electricity  can  cause  severe  injuries  even  with  low  voltage  or 
currents.  Therefore  it  is  extremely  important  that  you  read  the 
following information before using your digital RCCB / ELCB tester.
1.1 This   instrument   must   only   be   used  and  operated  by  a 
      competent  trained  person  and  in  strict  accordance with the 
      instructions.  We  will  not  accept  liability  for  any  damage or 
      injury  caused  by  misuse  or non compliance with instructions
      and safety procedures.
1.2 Never open your digital RCCB / ELCB tester except for battery
      replacement. (See Battery Replacement section).
1.3 Always  inspect  you digital RCCB / ELCB tester and test leads
      before  use  for  any  sign  of  abnormality  or  damage.  If  any
      abnormal  conditions  exist  (broken  test leads,  cracked case,
      display faulty etc.) do not attempt to take any measurement or
      use the tester. Return your digital RCCB / ELCB tester to your
      nearest Distributor for service.
1.4 Never  replace  the  protective  fuse  with  any  other  than  the 
      specified or approved equivalent.
1.5 Your  digital  RCCB / ELCB tester has been designed with your 
      safety   in  mind.  However, no design  can  completely  protect 
      against incorrect use. Electrical circuits can be dangerous and/
      or lethal when a lack of caution or poor safety practice is used.
      Be careful of the voltage presented above 24V as  these  pose 
      a shock Hazard.
1.6 Pay attention to cautions and warnings which will inform you of
      potentially dangerous procedures.
1.7 Rated environmental conditions :

(1) Indoor use.
(2) Installation Category III.
(3) Pollution Degree 2.
(4) Altitude up to 2000 Meters.
(5) Relative Humidity 80% Maximum.
(6) Ambient Temperature 0-40ºC.

2. SPECIFICATIONS :

Current Settings

Current Selection
Phase Start Selection
0º and 180º
Over-Temperature Protection
Wiring Correctness indication
Trip Indicator
Phase Polarity Trip Indicator
Operating Voltage (L-E) 50Hz or 60Hz
1812EL-A
1812EL-B
1812EL-C
1812EL-D
Voltmeter (L-E)
Timer Resolution
Timer Accuracy
Current Accuracy
Voltmeter Resolution
Voltmeter Accuracy
Operating Temperature
Storage Temperature
Battery

Current Specified at

3ma, 5mA, 7mA, 10mA,
15mA, 20mA, 30mA,35mA,
50mA, 100mA, 125mA, 
150mA, 175mA,
250mA, 300mA, 375mA,
500mA.
Rotary Switch 
Referenced to Earth
Yes
Yes (3 sensors)
Yes (LEDs)
Yes (LCD)
Yes (LCD)
Referenced to Earth

240Vac
230Vac
220Vac
110Vac
20Vac-280Vac
1mS (max time= 2.999S)
±2% rdg ±2mS
±5% ±1mA
1Vac
±2% ±1Vac
-5ºC to 45ºC
-10ºC to 85ºC

´

 AA batteries

Bat OK Led = Vbat >7.5v
Measure battery voltage at 
start up
Operating voltage

Summary of Contents for KM 1812EL








Reviews: