background image

15

EN

G

Index

Page

Description of the appliance

15

Instructions for use

15

Programming timer

15

Cleaning and maintenance

16

Problem solving

16

Sizes and specifications

17

Accessories supplied

18

Installation

18

Active charcoal filters

18

A

An electronic programmer device with

TOUCH CONTROL technology to control

speed, light, programming and power

indicators in use as well as filter saturation.

B

Metal filters.

C

Lamp with two bulbs - 20 W (G-4).

D, E

Vertically adjustable tubecovers.

F

Decorative part.

G

Remote control (Optional).

Switch on the extractor fan a few minutes

before you start to cook in order to ensure that

a steady air flow has been established before

fumes appear.

Allow the extractor fan to run for several

minutes after you have finished cooking

(between 3 to 5 minutes) in order to expel all

the grease from the outlet duct. This prevents

the return of grease, smoke and smells.

Proceed as follows:

1) Turn the kitchen hood on and choose the

required speed. Press "timer". Suction

indicators 1, 2 and 3 will start to flash.

2) Select the required time by pressing the

increase and decrease speed selectors.

There is a variation of 10 in 10 minutes.

(Min.= 10 min.; Max.= 30 min.)

3) Once the required time has been selected,

press "timer" again to memorise the

program. The speed indicator in use will

start to flash.

4)Intensive

“H”

suction

cannot

be

programmed as it has a set length of 10

minutes.

Fig. 3 (Page 19)

• Do not mix used batteries with new ones.

• Do not heaten up batteries nor put them

into fire.

• Do not damage nor short-circuit batteries.

• Remove batteries from the remote control

if it will not be used for a longer time. Store

batteries in a dry and cool place.

Clean the filters when the saturation indicator

lights up. (See page 16, Filter cleaning

section).

Once you have cleaned the filters, and with

the hood turned off, press the increase and

decrease speed buttons at the same time for

3 seconds and the indicator will switch itself

off.

Description of the appliance

Instructions for use

Programming timer

You may control the kitchen hood by operating the

controls as shown in the diagram.

Filter saturation indicators

Remote control (Optional)

Summary of Contents for KD 9760.0 GE








Reviews: