background image

23

Installation

Positioning

The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc.
Best performance is obtained with ambient
temperature b18°C and +43°C (class T);
+18°C and +38°C (class ST); +16°C and +32°C
(class N); +10°C and +32°C (class SN).

The class of your appliance is shown on its
rating plate.

For building-in and door reversibility refer to the
relevant instructions.

Electrical connection

Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply.
Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized
auto-transformer must be used.

Important
The appliance must be earthed.

The power supply cable plug is provided with a
contact for this purpose.
If the domestic power supply socket is not
earthed. connect the appliance to a separate
earth in compliance with current regulations,
consulting a specialist technician.

The Manufacturer declines all
responsibility if the above safety
precautions are not observed.

Attention!

It must be possible to disconnect the appliance

from the mains power supply; the plug must
therefore be easily accessible after installation.

This appliance complies with the following E.E.C. Directives:

- 87/308 EEC of 2/6/87 relative to radio

interference suppression.

- 73/23 EEC of 19.2.73 (Low Voltage
Directive) and subsequent modifications.
- 89/336 EEC of 3.5.89 (Electromagnetic 

Compatibility Directive) and subsequent 
modifications.

Grid preparation

Left door opening:

Remove the left side (A) of the grid cutting it from the
rear (see figure).

Right door opening:

Remove the right side (B) of the grid cutting it from
the rear (see figure).
To position the grid on the appliance proceed as follows:
Apply the grid to the base of the appliance by
pushing on to the clasps (a) until they click.

DO002/2

A

B

DO001

a

a

Building in the appliance under a worktop

Dimensions of the recess

The dimensions of the recessed installation area
must correspond with those indicated in the figure.

DO013

600

550

min.

600

Installation kit

1xA

2xD

1xB

2xC

2xL

18xI

2xF

2xG

1xK

1

Summary of Contents for IKU 159-0














Reviews: