background image

What to do if trouble occurs

 

Danger!

 The cooker hood may only be repaired by an authorised

technician.

 

Danger! 

For repair work the appliance must be disconnected from 

the power supply by pulling out the mains plug or unscrewing the 
household fuse.

First check whether there has been any operating error. You can deal with
some problems that occur yourself.

Problem

Cause Remedy

It is not possible to
switch off the cooker
hood.

Electronic component is
defective.

Pull out plug or switch off
fuse,
Call Customer Service.

Halogen lighting
does not work.

Lamp defective

Replace lamp.

LED does not work.

LED defective.

Call Customer Service.

Performance of the
cooker hood is
reduced.

Filters very clogged.

Replace filters.

Several LEDs flash.

Not a defect

see “Cleaning the metal
fat filters”.

Rating label

The rating label can be seen when you have removed the fat filter or the
activated charcoal filters. Please make a note of the following data on the
rating label before or while installing the cooker hood in case you have to
consult our Customer Service:

Serial number:

Model designation:

16

KD 966.1 / KDEM 966.1

Summary of Contents for IKD 966.1











Reviews: