Küppersbusch IGV 456.1 Instruction Book Download Page 16

In this fully integrated appliance the controls are located on the
top of the door. When selecting a programme, the door needs
to be open.

1. Check that the baskets have been 

loaded correctly and that the spray 
arms can rotate freely 

2. Turn on the water tap

3. Press the On/Off button

All the indicator lights of the programme selection buttons 
illuminate (setting mode).

4. Setting and starting the programme 

To select a programme, press the programme button of 
the washing programme you wish to select (see "Washing 
programmes" chart).

The corresponding indicator light remains illuminated 
while the other programme buttons indicator lights turn off.

The start of the programme will occur only after the 
closure of the door, until this moment you can modify the 
selection made.

Close the dishwasher door, the programme will start 
automatically.

5. To interrupt or cancel a washing 

programme in progress

Interrupt or cancel a washing programme in progress 
ONLY if it’s absolutely necessary

Attention! Hot steam may escape when the door is 
opened. Open the door carefully.

Interrupt a washing programme in progress

Open the dishwasher door; the programme will stop. 
Close the door; the programme will start from the point in 
which it was interrupted.

Cancel a washing programme in progress

Open the dishwasher door. 
Press simultaneously the function buttons and for 
about 2 seconds, the indicator light of the button 
corresponding to the running programme starts flashing for 
about 2 seconds. 
After about 2 seconds the indicator lights of all the 
programme buttons will illuminate indicating that the 
running programme has been cancelled and that the 
machine has returned to setting mode. 

(If a new washing programme will be selected, check that 
there is detergent in the detergent dispenser).

6. End of the washing programme

The dishwasher will automatically stop and an audible 
signal informs you of the end of the washing programme.

If the door is not immediately opened at the end of the 
programme, air will circulate inside the dishwasher to 
prevent residual steam recondensing on the dishes as 
water droplets.
This device operates intermittently for about 20 
minutes, as long as the dishwasher is switched on.
If the On/Off button is pressed or the door is opened 
during these 20 minutes, the device will be automatically 
cancelled.

Open the door, the end indicator light is illuminated.

The indicator light of the programme just ended remains 
on.

Switch off the dishwasher by pressing the On/Off button.

Wait a few minutes before removing the dishes; in this way 
they will be cooler and the drying will be improved.

7. Unloading the dishwasher

Hot dishes are sensitive to knocks. The dishes should 
therefore be allowed to cool down before removing from 
the appliance.
Empty the lower basket first and then the upper one; this 
will avoid water dripping from the upper basket onto the 
dishes in the lower one.
Water may appear on the sides and the door of the 
dishwasher as the stainless steel will eventually become 
cooler than the dishes.

When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.

"3 in 1" function

This function can be selected together with all programmes.

Place the "3 in 1" combi detergent tablet in the detergent
dispenser.

Press the "On/Off" button.

Press the "3 in 1" function button: the correspondent 
indicator light illuminates. Remember that if this function is
selected, it will remain active also for the following
programmes, until it will be deactivated by pressing the "3 in
1" 
function button (indicator light off).

Select the required washing programme.

Close the dishwasher’s door. The programme will start
automatically.

Once the programme is running, the "3 in 1" function can
NO longer be changed. If you want to exclude the "3 in 1"
function you have to cancel the programme setting (see 
"To cancel a washing programme in progress") and then 
deactivate the "3 in 1" function by pressing the "3 in 1"
button. 
In this case you have to set a washing programme again.

With the use of "3 in 1" combi detergent tablets, the cycle 
durations given in the "Washing programmes" chart may 
change.

Starting a washing programme

35

Summary of Contents for IGV 456.1





















Reviews: