Kuppersbusch IGV 6504.3 Instruction Manual Download Page 4

 

Safety instructions 

 

 

2 

 

1.  Safety and operating instructions 

 

 

THIS  MANUAL  FORMS  AN  INTEGRAL  PART  OF  THE  APPLIANCE:  IT  MUST 
ALWAYS  BE  KEPT  INTACT  TOGETHER  WITH  THE  DISHWASHER.  BEFORE 
USING  THE  APPLIANCE,  CAREFULLY  READ  ALL  THE  INSTRUCTIONS 
CONTAINED IN THIS MANUAL.  
INSTALLATION  MUST  BE  PERFORMED  BY  A  QUALIFIED  TECHNICIAN,  IN 
COMPLIANCE  WITH  THE  REGULATIONS  IN  FORCE.  THIS  APPLIANCE  IS 
INTENDED  FOR  DOMESTIC  USE  AND  SIMILAR  APPLICATIONS  SUCH  AS 
THE  STAFF  KITCHENS  OF  SHOPS,  OFFICES  AND  OTHER  WORKPLACES, 
INSTITUTIONS,  AND  FOR  THE  USE  OF  GUESTS  AT  HOTELS,  HOSTELS, 
BED  AND  BREAKFAST  ESTABLISHMENTS  AND  OTHER  RESIDENTIAL 
FACILITIES 

AND 

COMPLIES 

WITH 

DIRECTIVES 

2006/95/EC 

AND 

2004/108/EC  CURRENTLY  IN  FORCE,  INCLUDING  THE  PREVENTION  AND 
ELIMINATION OF RADIO FREQUENCY INTERFERENCE. 
THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE: WASHING 
AND  DRYING  OF  DISHES
;  ANY  OTHER  USE  SHALL  BE  CONSIDERED 
IMPROPER.  THE  MANUFACTURER  DECLINES  ALL  RESPONSIBILITY  FOR 
USES OTHER THAN THOSE DESCRIBED ABOVE.
 

 

 

THE  NAME  PLATE  FEATURING  THE  TECHNICAL  DATA,  SERIAL  NUMBER 
AND  MARKINGS  IS  VISIBLY  POSITIONED  ON  THE  INNER  EDGE  OF  THE 
DOOR.  THE  NAME  PLATE  ON  THE  INNER  EDGE  OF  THE  DOOR  MUST 
NEVER BE REMOVED.
 

 

 

DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED 
WITHIN  THE  HOME.  SEPARATE  THE  VARIOUS  MATERIALS  WHICH  MAKE 
UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE 
COLLECTION CENTRE. 

 

 

THE  APPLIANCE  MUST  BE  PROVIDED  WITH  AN  EARTH  CONNECTION  IN 
ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE. 
THE MANUFACTURER DECLINES  ALL RESPONSIBILITY FOR DAMAGE TO 
PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE 
APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
 

 

 

IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR, 
ENSURE  THAT  THE  OPENINGS  ON  ITS  UNDERSIDE  ARE  NOT 
OBSTRUCTED. 

 

 

ALWAYS  SWITCH  OFF  THE  DISHWASHER  AFTER  EACH  USE  TO  AVOID 
WASTING ELECTRICITY. 

 

 

IN  THE  EVENT  OF  A  FAULT,  DISCONNECT  THE  DISHWASHER  FROM  THE 
ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP.  

 

 

DO NOT USE STEAM CLEANERS TO CLEAN THE DISHWASHER. 

 

Summary of Contents for IGV 6504.3








































Reviews: