Kuppersbusch ER 7534 I Operating Instructions Manual Download Page 8

19

ATTENTION!

It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.

Door reversibility

The appliance is supplied with the right

door opening. To change the opening
direction of the door proceed as in the
following instructions before installing it.

1. Unscrew the upper pin and remove the spacer

2. Remove the upper door

3. Unscrew the middle hinge and the plugs and refit

them on the opposite side

4. Refit the upper door, the upper pin and the

spacer on the opposite side

5. Unscrew the lower pin and remove the spacer

and refit them on the opposite side

The Manufacturer declines all responsibility if
the above safety precautions are not observed.

This appliance complies with the following

E.E.C. Directives:

- 87/308 EEC

of 2/6/87 relative to radio interference

suppression.

- 73/23 EEC

of 19.2.73 (Low Voltage Directive) and

subsequent modifications;

- 89/336 EEC

of 3.5.89 (Electromagnetic

Compatibility Directive) and subsequent
modifications.

Instructions for totally built-in appliances

50 mm

min.

200 cm

2

200 cm

2

min.

D567

Building-in instructions

Dimensions of housing

Height 1225 

mm

Depth 550 

mm

Width 560 

mm

For safety reasons, minimum ventilation must be as
shown in Fig.

Attention: keep ventilation openings clear of
obstruction.

Summary of Contents for ER 7534 I












Reviews: