KUHN SpeedRake SR108 Operator'S Manual Download Page 38 | Manualshive

Page: 38 / 44

background image

SpeedRake

36

SR108 SR110 SR112

Maintenance and storage

$

Maintenance and storage

1. Lubrication

The pictorials show the points to be greased.

Clean grease zerks before greasing.



Every 25 hours

- Primary pivot (1)

- Twin rake wheel mount pivot (2)

- Rake wheel hubs (3)

- Link bar pins (4)

Before leaving the tractor or before
adjusting, maintaining or repairing the
machine, always perform the safety
shutdown procedure.

4

3

1

2

3

«
...
36
37
38
39
40
...
»

Summary of Contents for SpeedRake SR108













































Reviews:

No comments

Related manuals for SpeedRake SR108

Brand: DARAY Pages: 24

Brand: Jafar Pages: 9

KOMPAN SPF28666S

Brand: Bommelland Pages: 23

Brand: Ace Pages: 17

Brand: ACE INSTRUMENTS Pages: 33

Brand: ACE INSTRUMENTS Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: TapFlo Pages: 35

Brand: DANA Pages: 8

Brand: 2E Pages: 6

Brand: Dana Design Pages: 20

Brand: XanLite Pages: 4

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 85

Brand: Yamaha Pages: 43

Brand: Yamaha Pages: 200

Brand: Zero88 Pages: 26

Brand: HAMOKI Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands