KUHN GMD16 Operator'S Manual Download Page 46

Page: 46 / 100

GMD16-GMD20

6. - Putting into service

KN225BGB_A

Disc mower

- Pull on handle (1) to unlock parking stand (2) (a).
- Raise and lock parking stand (b).
- Lock tractor lower link stabilisers.

6.2.5 Hydraulic connections

- Connect hydraulic hose (1) of the transport/work

cylinder to a single acting valve with float position.

6.2.6 Electrical connection

6.2.7 Fit check chain

When optional equipment is used, follow
specific procedures mentioned in the related
section:

•

Optional equipment / Manual

hydraulic cutter bar lift pump.

When optional equipment is used, follow
specific procedures mentioned in the related
section:

• Optional equipment / Lighting and

signalling.

See section: Putting into service / Coupling and
uncoupling / Adjusting the machine / Frame
height and check chains.

Summary of Contents for GMD16





































































































Search results

Summary of Contents for GMD16

Reviews:

Related manuals for GMD16

Brands by name

Popular brands

KUHN GMD16, Operator'S Manual

Search results

Summary of Contents for GMD16

Reviews:

Related manuals for GMD16

Brands by name

Popular brands