Kubota WSM L3540-II Workshop Manual Download Page 44 | Manualshive

Page: 44 / 672

background image

GENERAL

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

G-22

Replacing Engine Oil Filter

WARNING

• Be sure to stop the engine before changing the oil filter

cartridge.

• Allow engine to cool down sufficiently, oil can be hot and

can burn.

1. Remove the oil filter.
2. Put a film of clean engine oil on the rubber seal of the new filter.
3. Tighten the filter quickly until it contacts the mounting surface.

Tighten filter by hand an additional 1/2 turn only.

4. After the new filter has been replaced, the engine oil normally

decreases a little. Make sure that the engine oil does not leak
through the seal and be sure to check the oil level on the
dipstick. Then, replenish the engine oil up to the prescribed
level.

IMPORTANT

• To prevent serious damage to the engine, use only a

KUBOTA genuine filter.

9Y1211167GEG0023US0

Checking Clutch Pedal Free Travel

1. Stop the engine and remove the key.
2. Slightly depress the clutch pedal and measure free travel

"L"

at

top of clutch pedal.

3. If the measurement is not within the factory specifications,

loosen the lock nut (2), remove the clevis pin (3) adjust the
length of rod (1) within acceptable limits.

4. Retighten the lock nut (2) and split the cotter pin.

9Y1211167GEG0024US0

(1) Engine Oil Filter

Clutch pedal free travel

"L"

Factory specification

20 to 30 mm
0.78 to 1.18 in.

(1) Clutch pedal Rod
(2) Lock Nut
(3) Clevis Pin

L : Free Travel

KiSC issued 02, 2015 A

«
...
42
43
44
45
46
...
»

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WSM L3540-II

Brand: Gram Pages: 48

Brand: Iseki Pages: 51

Brand: Winton Pages: 40

LS Tractor LW3150

Brand: RadTech Pages: 44

Brand: New Holland Pages: 2

Brand: Zetor Pages: 236

Brand: Land Pride Pages: 32

Brand: Hardi Pages: 170

Brand: Barko Pages: 174

Brand: MAGNATRAC Pages: 86

Brand: Zetor Pages: 41

Brand: Metal-Fach Pages: 42

Brand: Pottinger Pages: 27

INUKTUN MICROTRAC

Brand: Eddyfi Technologies Pages: 26

Brand: Agromehanika Pages: 90

Brand: Agromehanika Pages: 245

Brand: MASSEY FERGUSON Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands