manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 63

GENERAL

G23, G26, WSM

G-45

(EU)

Replacing Fuel Filter

1. Disconnect the fuel hoses and replace the fuel filter (3).
2. Disconnect the fuel hoses and loosen the pipe clamps to

replace the fuel filter (5).

NOTE

• If the fuel hose is removed, be sure to properly bleed the

fuel system. (See page G-49.)

9Y1210294GEG0050US0

[8] CHECK POINT OF EVERY 1500 HOURS

Checking Injection Nozzle Injection Pressure

• See page 1-S22.

9Y1210294GEG0051US0

[9] CHECK POINT OF EVERY 3000 HOURS

Checking Injection Pump

• See page 1-S21.

9Y1210294GEG0052US0

[10] CHECK POINT OF EVERY 1 YEAR

Replacing Air Cleaner Element

• See page G-32.

9Y1210294GEG0053US0

[11] CHECK POINTS OF EVERY 2 YEARS

Replacing Fuel Lines

1. Replace the hose and the clamps.

Refer to "Checking Fuel Line and Fuel Filter". (See page G-38.)

9Y1210294GEG0054US0

Replacing Hydraulic Hose

1. Replace hoses and hose clamps every 2 years or earlier if

checked and found that hoses are swollen, hardened or
cracked. (See page G-41.)

9Y1210294GEG0055US0

Replacing Radiator Hose

1. Replace hoses and clamp bands every 2 years or earlier if

checked and found that hoses are swollen, hardened or
cracked. (See page G-43.)

9Y1210294GEG0057US0

(1) Fuel Hose
(2) Pipe Clamp
(3) Fuel Pump and Filter

(4) Fuel Line
(5) Fuel Filter
(6) Pipe Clamp

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands