Kubota G23 Workshop Manual Download Page 104

Page: 104 / 343

ENGINE

G23, G26, WSM

1-S22

(EU)

CAUTION

• Check the nozzle injection pressure and condition after confirming that there is nobody standing in the

direction the fume goes. If the fume from the nozzle directly contacts the human body, cells may be
destroyed and blood poisoning may be caused.

9Y1210294ENS0016US0

Nozzle Spraying Condition

1. Set the injection nozzle to a nozzle tester, and check the nozzle

spraying condition.

2. If the spraying condition is defective, replace the nozzle piece.

9Y1210278ENS0013US0

Fuel Injection Pressure

1. Set the injection nozzle to a nozzle tester.
2. Slowly move the tester handle to measure the pressure at which

fuel begins jetting out from the nozzle.

3. If the measurement is not within the factory specifications,

replace the adjusting washer (1) in the nozzle holder to adjust it.

(Reference)

• Pressure variation with 0.01 mm (0.0004 in.) difference of

adjusting washer thickness.
Approx. 235 kPa (2.4 kgf/cm

, 34.1 psi)

9Y1210294ENS0017US0

Valve Seat Tightness

1. Set the injection nozzle to a nozzle tester.
2. Raise the fuel pressure, and keep at 12.75 MPa (130.0 kgf/cm

1849 psi) for 10 seconds.

3. If any fuel leak is found, replace the nozzle piece.

9Y1210278ENS0015US0

(a) Good

(b) Bad

Fuel injection pressure

Factory specification

13.73 to 14.70 MPa
140.0 to 150.0 kgf/cm

1991 to 2132 psi

(1) Adjusting Washer

Valve seat tightness

Factory specification

No fuel leak at
12.75 MPa
130.0 kgf/cm

1849 psi

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands