Kubota AP-SD96 Operator'S Manual Download Page 16

Page: 16 / 36

Section 1: Optional Equipment & Set-up

AP-SD96 Silage Defacer 350-270MK

9/3/19

Table of Contents

Tractor Loader Hose Kit Assembly

Tractor Loader Hose Kit . . . . . . . . . . . . . . . 350-267A

WARNING

To avoid serious injury or death:

•

Hydraulic fluid under high pressure can penetrate the skin

and/or eyes causing a serious injury. Wear protective gloves

and safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than

hands when searching for leaks. A doctor familiar with this

type of injury must treat the injury within a few hours or

gangrene may result. DO NOT DELAY.

•

Shut power machine down and release all hydraulic

pressure to the equipment before connecting or

disconnecting hydraulic hoses to or from the power

machine.

Refer to

Figure 1-3:

1. Attach elbow fitting (#4) to top port of hydraulic motor

(#3). Attach elbow fitting (#5) to bottom port of

hydraulic motor (#3).

2. Attach in-line valve fitting (#6) to elbow fitting (#5).
3. Attach and tighten female ends of hydraulic

hoses (#1 & #2) to hydraulic fittings (#4 & #6),

respectively.

4. Remove hose cover (#12), hose clamp brackets (#13)

and all hardware items (#9, #10, & #11) from welded

hex bolts (#7) found on the left side of hitch

frame (#14). Keep removed hardware close by.

5. Route hydraulic hoses (#1 & #2) from hydraulic

motor (#3), to the welded hex bolt (#7) closest to

hydraulic motor (#3).

6. Place hydraulic hose (#1) above hex bolt (#7) and

hydraulic hose (#2) below hex bolt (#7).

Secure hydraulic hoses (#1 & #2) by fastening hose

clamp bracket (#13), lock washer (#10) and hex

nut (#11) to hex bolt (#7). Tighten hex nut (#11) to the

correct torque. Refer to

“Section 8: Torque Values

Chart”

on page 28.

8. Continue routing hydraulic hoses (#1 & #2) along side

of hitch frame (#14). Repeat steps 6 and 7 to secure

hoses at second welded hex bolt (#7) found on left

side of hitch frame (#14).

9. Secure hose cover (#12) to both welded hex

bolts (#7) with flat washers (#9), lock washers (#10),

and 1/4" hex nuts (#11). Tighten hex nuts (#11) to the

correct torque.

10. Route hydraulic hoses (#1 & #2) between upper and

lower tubes of hitch frame (#14)

11. Secure hydraulic hoses (#1 & #2) to welded hex bolt

(#7) on hitch frame center tube (#15) with hose clamp

bracket (#13), flat washer (#9), lock washer (#10),

and 1/4" hex nut (#11). Tighten hex nut (#11) to the

correct torque. See detail B.

12. Route hydraulic hoses (#1 & #2) through formed

D-ring (#8).

13. Thread quick disconnect male fitting (#1A) onto male

end of hydraulic hose (#1). Thread quick disconnect

female fitting (#2A) onto male end of hydraulic

hose (#2).

14. The Silage Defacer is now ready to hook-up to a

tractor with a compatible front loader.

Tractor Loader Hose Kit Assembly

Figure 1-3

Detail A

72171

Detail B

72613

72170

Summary of Contents for AP-SD96





































Search results

Summary of Contents for AP-SD96

Reviews:

Brands by name

Popular brands

Kubota AP-SD96, Operator'S Manual

Search results

Summary of Contents for AP-SD96

Reviews:

Brands by name

Popular brands