manualshive.com logo in svg

Kubota AP-SA35, Operator'S Manual

Share
Download
Kubota AP-SA35 Operator'S Manual Download Page 16

Section 1: Assembly & Set-up 

Table of Contents

4/9/19

AP-SA35 Hydraulic Post Hole Digger 317-093MK

12

o

Kubota Hose Stay Kit

Figure 1-7

2.

Clean quick disconnect couplers of dirt and connect 
male and female couplers to the Skid Steer/Tractor 
high pressure outlets. Make sure they have fully 
engaged. If they have not, check the followings:

•

Make sure couplers are same size and type.

•

Make sure hydraulic pressure has been released.

3.

Make sure hoses are kept away from all pinch points 
and then zip tie hoses together as needed. Two zip 
ties are provided for this purpose.

4.

Operate Skid Steer/Tractor to check auger rotation. 
The auger should rotate clockwise when looking 
down from above. If auger rotates counterclockwise, 
switch male and female couplers on the hydraulic 
hoses and then reconnect hoses to the outlets. 

5.

Also see Hydraulic Hook-up instructions in your Skid 
Steer/Tractor Operator’s Manual.

Auger Assembly

Refer to Figure 1-8:

1.

Position mounting holes in auger tube (#3) in line 
with hole in gearbox output shaft (#4). 

37393

Hose Stay Kit

NOTE:  

If attaching to a Kubota skid steer, route 

hydraulic hoses through Kubota’s SVL or SSV Hose 
Stay as shown in Figure 1-7. Purchase 

SVL Hose 

Stay #S6689 or SSV Hose Stay #77700-07225 

through your nearest Kubota dealer. Refer to your 
skid steer Operator’s Manual for more instructions.

NOTE:  

Augers are supplied with either a 2 9/16" dia. 

round hub or 2" hex hub. Make sure gearbox output 
shaft matches the auger hub.

Auger Screw Assembly

Figure 1-8

2.

Slide auger tube (#3) over gearbox output shaft (#4) 
and install:

•

Round Hub - 7/8"-9 x 5" GR5 cap screw (#1) and 
nylock nut (#2). 

•

Hex Hub - 3/4"- 10 x 4 1/2" GR5 cap screw (#1) and 
nylock nut (#2).

3.

Tighten hardware to proper torque. 

19232

Clockwise Rotation

Auger Tip

Hydraulic Hoses

Auger Flighting

Summary of Contents for AP-SA35



































Reviews:

No comments

Brands by name

Popular brands

Load more brands