Kubota 329-181A Assembly Instructions Manual Download Page 3

Page: 3 / 16

Assembly Instructions

5/21/21

PS20 Seed Cup Speed Increaser Kit 329-181A Assembly Instructions Manual No. 329-242MK

Installing Upper Drive Sub-assembly

Installing the new upper drive sub-assembly at this time

will aid in determining the locations and angles for

installing the new chain guard mounts.

Refer to Figure 1-2 & Figure 1-3:

1. Raise seedbox lid (J) for hardware installation.
2. Position new upper drive sub-assembly at location

where pre-existing upper drive sub-assembly (D)

was removed from.
a. Secure upper drive sub-assembly to the

machine with two 5/16-18x1 GR5 bolts (#28),

flat washers (#42), lock washers (#40), and hex

nuts (#34).

b. Tighten hardware to 17 ft-lbs (24 N

m).

Installing Upper Drive Sub-assembly

Figure 1-2

3. Hook tension spring (#46) onto the notches of both

tensioner arms (#5) as shown in Figure 1-3.

Installing Tension Spring

Figure 1-3

NOTE:

The new upper drive sub-assembly comes

partially pre-assembled. The remaining components

will be assembled during a later procedure.

76262

Upper drive

sub-assembly

Hex shaft (#14) &

sprocket (#6) removed

from illustration for

clarity purposes only.

76289

Installing New Chain Guard Mounts

WARNING

To avoid serious injury or death:
Wear the appropriate personal protective equipment and

clothing when performing tasks such as using a cutting torch,

grinding, and/or welding.

Refer to Figure 1-4 & Figure 1-5 on page 4:

1. Ensure area where new chain guard mounts are to

be welded are void of gouges, and/or excess material

that still needs to be removed.

2. Measure out and mark locations on seeder frame for

placement of new chain guard mounts (#11 & #12).

Refer to Figure 1-4 below for the needed dimensions.

New Chain Guard Mount Specifications

Figure 1-4

3. Secure both chain guard mounts (#11 & #12) to new

chain guard (#10) with two hand knobs (B). This will

set the angle needed for each chain guard mount.

Refer to Figure 1-5 on page 4.

4. Mount and secure chain guard (#10) to the top of

upper drive sub-assembly mount (#4) with the last

hand knob (B).

5. Verify that each chain guard mount is lined up to the

measured out markings made in step 2.

NOTE:

To achieve a good arc for welding, proper

penetration, and contaminant free welds, ensure

paint has been removed from the seeder’s steel

frame where the new chain guard mounts

(#11 & #12) will be welded to.

76273

Detailed View with Specs

0.09"

9.44"

0.19"
0.19"

Seeder frame

& side panel

Summary of Contents for 329-181A

















Search results

Summary of Contents for 329-181A

Reviews:

Brands by name

Popular brands

Kubota 329-181A, Assembly Instructions Manual

Search results

Summary of Contents for 329-181A

Reviews:

Brands by name

Popular brands