KTM 50 SX Mini Repair Manual Download

Page: 43 / 159

06/AIR FILTER

8.1

Removing the air filter

Note

Engine failure

Unfiltered intake air has a negative effect on the service life of the engine.

–

Never ride the vehicle without an air filter since dust and dirt can get into the engine and result in increased wear.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

–

Remove the seat. (

p. 42)

700504-01

–

Press the rear holding lugs



together slightly and swing the air filer cover upward.

Pull out the front holding lug and take off the air filter cover.

–

Take off the air filter.

8.2

Installing the air filter

700505-01

–

Position the clean air filter.

–

Position the rear holding lug. Lower the air filter cover and allow the front holding
lug



to snap in.

Info

If the air filter is not correctly mounted, dust and dirt can penetrate into the
engine and can cause damage.

–

Mount the seat. (

p. 42)

8.3

Cleaning air filter

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Do not clean the air filter with fuel or petroleum since these substances attack the foam.

–

Remove the air filter. (

p. 41)

–

Wash the air filter thoroughly in special cleaning liquid and allow it to dry properly.

Air filter cleaner (

p. 144)

Info

Only press the air filter to dry it, never wring it out.

–

Oil the dry air filter with a high/quality filter oil.

Oil for foam air filter (

p. 145)

–

Clean the air filter box.

–

Check carburetor connection boot for damage and tightness.

–

Install the air filter. (

p. 41)

PartShark.com

877-999-5686

Summary of Contents for 50 SX Mini
































































































































































Search results

Summary of Contents for 50 SX Mini

Reviews:

Related manuals for 50 SX Mini

Brands by name

Popular brands

KTM 50 SX Mini, Repair Manual

Search results

Summary of Contents for 50 SX Mini

Reviews:

Related manuals for 50 SX Mini

Brands by name

Popular brands