manualshive.com logo in svg

KTI Networks KS2028, Installation Manual

Share
Download
KTI Networks KS2028 Installation Manual Download Page 19

3.3 10/100BASE-TX Switched Ports

This section applies to the 10/100BASE-TX Port #9 and expansion slot
Port #10 pre-configured with a 10/100BASE-TX port module. Use the
crossover switch to set the type of RJ-45 connector as follows:

     

The following table lists the devices to which the ports can connect:

Device connected

Crossover SW

Cable used

Computer 10BASE-T port

X setting

Cat. 3, 5 straight UTP

10BASE-T hub port (I type)

X setting

Cat. 3, 5 straight UTP

10BASE-T hub port (X type)

I setting

Cat. 3, 5 straight UTP

10BASE-T switched port (I type)

X setting

Cat. 3, 5 straight UTP

10BASE-T switched port (X type)

I setting

Cat. 3, 5 straight UTP

100BASE-TX hub port (I type)

X setting

Cat. 5 straight UTP

100BASE-TX hub port (X type)

I setting

Cat. 5 straight UTP

100BASE-TX switched port (I type)

X setting

Cat. 5 straight UTP

100BASE-TX switched port (X  type)

I setting

Cat. 5 straight UTP

Cable Type and Maximum Length

Connection

UTP Cable Category

Maximum length

10BASE-T (10Mbps)

Cat. 3, 5

100 meters

100BASE-TX (100Mbps)

Cat. 5

100 meters

14

Summary of Contents for KS2028






















Reviews:

No comments

Brands by name

Popular brands

Load more brands