KSB UPA Installation & Operating Manual Download Page 7

Page: 7 / 98

1 General

7 of 98

UPA / UPA S

3400.86/17-EN

1.3 Other applicable documentation

Table 1:

Overview of other applicable documents

Document

Contents

Data sheet

Description of the technical data of the pump (set)

General arrangement drawing /
outline drawing

Description of mating dimensions and installation
dimensions for the pump (set), weights

Hydraulic characteristic curve

Characteristic curves showing head,
NPSH required, efficiency and power input

General assembly drawing

Description of the pump in a sectional drawing

Description of the motor in a sectional drawing

Sub-supplier product literature

Operating manuals and other product literature
describing accessories and integrated machinery
components

Spare parts lists

Description of spare parts

Operating manual for accessories

Description of accessories, e.g. cable connectors

For accessories and/or integrated machinery components, observe the relevant
manufacturer's product literature.

1.4 Symbols

Table 2:

Symbols used in this manual

Symbol

Description

✓

Conditions which need to be fulfilled before proceeding with the
step-by-step instructions

⊳

Safety instructions

⇨

Result of an action

⇨

Cross-references

Step-by-step instructions

Note
Recommendations and important information on how to handle
the product

If included in agreed scope of supply

Summary of Contents for UPA



































































































Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands

KSB UPA, Installation & Operating Manual

Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands