KSB HPK-L Installation & Operating Manual Download Page 49 | Manualshive

Page: 49 / 74

background image

7 Servicing/Maintenance

49 of 74

HPK-L

1136.8/15-EN

7.3 Drainage/cleaning

WARNING

Fluids handled, consumables and supplies which are hot and/or pose a health
hazard

Hazard to persons and the environment!

▷

Collect and properly dispose of flushing fluid and any fluid residues.

▷

Wear safety clothing and a protective mask if required.

▷

Observe all legal regulations on the disposal of fluids posing a health hazard.

If the pump set has handled fluids whose residues could lead to corrosion damage in
the presence of atmospheric humidity or could ignite upon contact with oxygen, the
pump set must be neutralised, and anhydrous inert gas must be blown through the
pump to ensure drying.

Use connection 6B to drain the fluid handled (see drawing of auxiliary connections).

7.4 Dismantling the pump set

7.4.1 General information/Safety regulations

DANGER

Insufficient preparation of work on the pump (set)

Risk of injury!

▷

Properly shut down the pump set.

▷

Close the shut-off elements in the suction line and discharge line.

▷

Drain the pump and release the pump pressure. (

Section 7.3, Page 49)

▷

Shut off any auxiliary connections.

▷

Allow the pump set to cool down to ambient temperature.

WARNING

Unqualified personnel performing work on the pump (set)

Risk of injury!

▷

Always have repair work and maintenance work performed by specially trained,
qualified personnel.

WARNING

Hot surface

Risk of injury!

▷

Allow the pump set to cool down to ambient temperature.

WARNING

Improper lifting/moving of heavy assemblies or components

Personal injury and damage to property!

▷

Use suitable transport devices, lifting equipment and lifting tackle to move
heavy assemblies or components.

«
...
47
48
49
50
51
...
»

Summary of Contents for HPK-L











































































Reviews:

No comments

Related manuals for HPK-L

Brand: DAB Pages: 8

Brand: Accorroni Pages: 40

Brand: A.O. Smith Pages: 2

Brand: DAB Pages: 13

Brand: Gardena Pages: 16

Brand: Gardena Pages: 9

Brand: Gardena Pages: 11

13000 aquasensor

Brand: Gardena Pages: 14

Brand: WarmPool Pages: 26

Brand: A.O. Smith Pages: 2

Residential Gas Water Heaters

Brand: A.O. Smith Pages: 84

Brand: CLIVET Pages: 7

Brand: Rinnai Pages: 67

Brand: esotec Pages: 2

Dura-Power Den & Del

Brand: A.O. Smith Pages: 2

Pacific Hydrostar 2" or 3" Dirty Water Pump...

Brand: Pacific hydrostar Pages: 36

Brand: Jebao Pages: 3

Brand: Calpeda Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands