Krone EasyCut B 870 CR Operating Instructions Manual Download Page 36

Page: 36 / 108

Control and Display Elements

5.1

Operation panel

EasyCut B 870 CR

Original Operating Instructions 150000706_01_en

Control and Display Elements

5.1

Operation panel

The operation panel is used to preselect different functions of the machine. The actual functions
are executed via the control units of the tractor. The following table explains the function of the
individual switches.

KMG000-001

Designation

Function

1 Red warning light

Is lit when the operation panel is switched on.

2 Toggle switch

Middle Operation panel OFF (warning light (1) OFF)

Top

Double-acting control unit (2+/2-)

(2-)

Lowers both mowers from transport position to head-
land position.

(2+)

Raises both mowers from headland position to trans-
port position.

Bottom Activates the lower toggle switch (3).

Summary of Contents for EasyCut B 870 CR













































































































Search results

Summary of Contents for EasyCut B 870 CR

Reviews:

Related manuals for EasyCut B 870 CR

Brands by name

Popular brands

Krone EasyCut B 870 CR, Operating Instructions Manual

Search results

Summary of Contents for EasyCut B 870 CR

Reviews:

Related manuals for EasyCut B 870 CR

Brands by name

Popular brands