Krone EasyCut B 870 CR Operating Instructions Manual Download Page 73

Page: 73 / 108

Maintenance - Gearbox

Gearbox for upper roller drive

13.4

EasyCut B 870 CR

Original Operating Instructions 150000706_01_en

13.4

Gearbox for upper roller drive

KM000-078

Observe the safety routine “Safely performing oil level check, oil change and filter element
change”,

refer to page 25

INFORMATION

The oil level must be checked and the oil must be changed in working position and with
machine in horizontal position.

Checking oil level

Unscrew the locking screw of the inspection hole (1).

If the oil reaches the inspection hole (1):

Mount the locking screw of the inspection hole (1), Anziehdrehmoment

refer to page 65

If the oil does not reach the inspection hole (1):

Unscrew the locking screw of the filling hole (3).

Top up new oil via the filling hole (3) up to the inspection hole (1).

Mount the locking screw of the inspection hole (1) and the locking screw of the filling
hole (3), Tightening torque

refer to page 65

Changing oil

A suitable container is available for escaping oil.

Unscrew the locking screw of the inspection hole (1) and the locking screw of the filling hole
(3).

Unscrew the drain plug (2) and drain the oil.

Mount the drain plug (2), tightening torque

refer to page 65

Top up new oil via the filling hole (3) up to the inspection hole (1).

Mount the locking screw of the inspection hole (1) and the locking screw of the filling hole
(3),Tightening torque

refer to page 65

Summary of Contents for EasyCut B 870 CR













































































































Search results

Summary of Contents for EasyCut B 870 CR

Reviews:

Related manuals for EasyCut B 870 CR

Brands by name

Popular brands

Krone EasyCut B 870 CR, Operating Instructions Manual

Search results

Summary of Contents for EasyCut B 870 CR

Reviews:

Related manuals for EasyCut B 870 CR

Brands by name

Popular brands