Kromschroder BCU 465 Technical Information Download Page 4

Page: 4 / 31

T-Product · BCU 465 · 2006 April

BCU 465T

Start

OCS

Application

The BCU 465 combines the func-

tionally related components of the

automatic burner control unit, igni-

tion transformer, manual/automatic

mode and a digital display for op-

erating parameter and fault status

indication in a single metal housing.

The BCU

controls the ignition

process and continuously monitors

the burner operation. The BCU

is designed to mount close to the

burner to reduce installation costs

and simplify commissioning and

troubleshooting efforts.

Application example

BCU 465 for Modulating Con-

trol Systems

The ﬁgure shows a typical modulat-

ing control system. The burner is

ignited when the air butterﬂy valve

is in the ignition position (low-ﬁre).

Once the burner is ignited, the air

butterﬂy valve can be modulated

throughout the control range. The

gas is controlled with an air/fuel

ratio regulator cross-connected to

the burner air supply piping.

Summary of Contents for BCU 465
































Search results

Summary of Contents for BCU 465

Reviews:

Related manuals for BCU 465

Brands by name

Popular brands

Kromschroder BCU 465, Technical Information

Search results

Summary of Contents for BCU 465

Reviews:

Related manuals for BCU 465

Brands by name

Popular brands