background image

 DEVICE DESCRIPTION 

2

11

VA FLOWMETERS

www.krohne.com

09/2022 - 4000419908 - AD VA Mech Ex Gb-Db R08 en

2.4  Flammable products

Atmospheric conditions:

The standard atmospheric conditions under which it may be assumed that Ex equipment can be 

operated are:

Temperature: -20...+60°C / -4...+140°F

Pressure: 80...110 kPa (0.8...1.1 bar) / 11.6...15.9 psi

Air with normal oxygen content, typically 21%v/v

Ex equipment operating outside the standard temperature range must be tested and certified 

(e.g. for ambient temperature range -40...+65°C / -40...+149°F).

 

Ex equipment operating outside the standard atmospheric pressure range and standard oxygen 

content is not permitted.

Operating conditions:

The measuring unit of variable area flowmeters operate outside the standard atmospheric 

pressure range, which means that explosion protection, regardless of the zone assignment, is 

fundamentally not applicable for the measuring unit (piping).

WARNING!

Operation with flammable products is only permitted as long as no explosive fuel/air mixture 

builds up inside of the piping at the same time the atmospheric conditions are exceeded.

 

The operator is responsible to ensure that the flowmeter is operated safely in terms of the 

temperature and pressure of the products used. In case of operation with flammable products 

the measuring units must be included in the periodic pressure tests of the piping.

 

The max. allowable operating pressure PS printed on the nameplate is to be considered.

 

The following versions require dust-free gases or liquids. Gases containing solid particles or 

liquid droplets are not permitted. The products must reach the stated minimum conductivity. 

The limit of the stated maximum nominal flow rate must be observed.

Device type

Minimum conductivity in µS/m

Maximum flow rate Q

max

H250/C...

0.01

-

VA40

0.001

5-times

GA24

-

10-times

DK46 / DK47 

 

DK48 / DK800

-

20-times

DK46PV / DK47PV 

 

DK48PV / DK800PV

0.001

20-times

Table 2-1: Minimum conductivity of product and maximum flow for the device type

Summary of Contents for DK 46





























Reviews: