KRK VXT 4 User Manual Download

Page: 15 / 16

Specifications

Model

VXT 4

VXT 6

VXT 8

Tweeter

1" Silk Dome NEO

1" Silk Dome Ferrite

Woofer

4" Woven Kevlar

6" Woven Kevlar

8" Woven Kevlar

Input Type

XLR-1/4" TRS Combo
10k Ohm Blanced
Pin 1 + Sleeve = Ground
Pin 2 + Tip = (+) High
Pin 3 + Ring = (-) Low

Controls

System Level Adjust

+6dB to -30dB Variable

Ground Lift

LFT (On) or GND (Off)

Clip Indicator

On, Off or Limit

Auto Mute

On or Off

HF Adjust - N/A

LF Adjust - N/A

System Level Adjust

+6dB to -30dB Variable

Ground Lift

LFT (On) or GND (Off)

Clip Indicator

On, Off or Limit

Auto Mute

On or Off

HF Adjust

+1dB, Flat, -1dB

LF Adjust

Whole Space (-3dB 52Hz)
Half Space (-3dB 60 Hz)
Quarter Space (-3dB 75Hz)

System Level Adjust

+6dB to -30dB Variable

Ground Lift

LFT (On) or GND (Off)

Clip Indicator

On, Off or Limit

Auto Mute

On or Off

HF Adjust

+1dB, Flat, -1dB

LF Adjust

Whole Space (-3dB 40Hz)
Half Space (-3dB 48 Hz)
Quarter Space (-3dB 62Hz)

Amp & Fusing

HF: 15 Watts
LF: 30 Watts
2.0A 100VAC 50HZ
2.0A 110-120VAC 50/60Hz
1.0A 220-240VAC 50/60Hz

HF: 30 Watts
LF: 60 Watts
3.15A 100VAC 50Hz
3.15A 110-120VAC 50/60Hz
1.6A 220-240VAC 50/60Hz

HF: 60 Watts
LF: 120 Watts
4.0A 100VAC 50Hz
4.0A 110-120VAC 50/60Hz
2.0A 220-240VAC 50/60Hz

Freq Response

56Hz - 22kHz +/- 2dB

49Hz - 22kHz +/-1.5dB

37Hz - 22kHz +/-1.5dB

Max SPL

Music: 104dB
Peak: 107dB

Music: 108dB
Peak: 111dB

Music: 111dB
Peak: 114dB

Dimensions

10 1/16" H x7 1/3" W x 7 " D
25.6cm H x 18.6cm W x 17.7cm

14 1/2" H x 10 1/3" W x 9 5/8" D
36.8cm H x 26.3cm W x 24.6cm D

17 1/4" H x 12 1/2" W x 11 7/8" D
43.8cm H x 31.8cm W x 30.0cmD

Shipping Weight

14 lbs

27 lbs

41 lbs

Omni Mount Part

20.5 WBX

30.0 WBX

60.0 WBX

Screw Type

Screw Length

12.5mm Min. - 17.5mm Max.

13.5mm Min. - 20.0mm Max.

17.75mm Min. - 26.0mm Max.

Summary of Contents for VXT 4

















Search results

Summary of Contents for VXT 4

Reviews:

Related manuals for VXT 4

Brands by name

Popular brands

KRK VXT 4, User Manual

Search results

Summary of Contents for VXT 4

Reviews:

Related manuals for VXT 4

Brands by name

Popular brands