manualshive.com logo in svg

Krendl GV180, Owner'S Manual, Page: 13 / 18

Share
Download
Krendl GV180 Owner'S Manual Download Page 13

Rev. Date: 11/11/20

Page 10

TROUBLE SHOOTING

Note: Whenever vacuum chamber cover is off, make sure key is taken out of the ignition switch.

Problem

Corrective Action

1) Gas vacuum will not start.

• Check engine oil level - (if low, unit will not start).

• Check engine fuel level.

• Make sure there is no foreign debris in the fan chamber impeding the motion

of the fan.

• Battery is low or dead.  Manually start vacuum with rewind starter. If

vacuum runs, battery may need charged or replaced.  If the battery is ok,

electric starter may need serviced. (See Briggs & Stratton manual.)

• Make sure spark plug wires are attached.

• Make sure fuel shut off valve is open.

• Verify hoses are installed and limit switches are engaged.

• Make sure spark plugs are clean and the correct plug for the appropriate

engine is used.  (See Briggs & Stratton manual.)

2) Excessive vibration.

• Make sure unit is sitting on a level surface.

• Make sure fan is properly secured to motor shaft.

• Check fan for damaged fins.

• Make sure there is no excessive insulation build up on the fan and in the

fan chamber.

• Fan may be out of balance and need replaced.

• Loose bolts on fan chamber cover.

3) Loud knocking.

• Make sure fan is properly secured to motor shaft.

• Make sure there is no foreign debris or fiber build up in the fan chamber.

4) Gas vacuum loses horsepower.

• Make sure there is no debris in fuel tank and fuel filter.  Clean or replace .

• Make sure there is no major insulation build up on the fan and in chamber.

• Make sure air filter is clean, replace if necessary.

5) Gas vacuum engine is stalling, smoking,

• Check engine fuel level - (Low fuel or no fuel).

or running irregularly.

• Make sure fuel shut off is completely open.

• Make sure gas vacuum is setting on level ground.

• Improper fuel may have been used. 

Use lead free gasoline with a

minimum of 85 octane.  Do not use gasoline which contains Metha-

nol. This will deteriorate the fuel line. Refer to owners manual.

•

Check for corrosion, build up, or foreign debris lodged in the float, pin, or seat.

This would cause inadequate performance. (Contact Briggs & Stratton dealer)

• Make sure engine oil level is not overfilled.

• Make sure air filter is clean, replace if necessary.

T

rouble 

S

hooting

Summary of Contents for GV180



















Reviews:

No comments