manualshive.com logo in svg

Krendl 4200-D, Owner'S Manual, Page: 8 / 38

Share
Download
Krendl 4200-D Owner'S Manual Download Page 8

Rev. Date: 1/3/12

Page 5

MODEL #4200-D

DECALS

Make Sure!

•

Hopper is empty of foreign objects 

before

 starting.

• Adequate electrical power is supplied or damage to unit will result.
• Machine must be on 

before

 adding fiber.

• Blower filter is kept clean and in place when blower is on.
• Machine is turned off 

immediately

 if hose is plugged, or blower will overheat.

• Blower must be on, when agitators are running, or machine will bind.
• Agitator motor is not run with hopper empty for more than a few minutes, or damage to seals will result.
• Sprockets, chains, belts and pulleys are correctly 

aligned

 and 

tensioned

.

• Pieces of bag are 

not

 left in the machine as this can bind and stall your machine.

• This machine should only be used with good quality fibers that are dry, undamaged and that meet a

certain industry specification or quality standards.

IF THERE ARE ANY QUESTIONS WITH YOUR KRENDL MACHINE, DO NOT HESITATE TO

CONTACT US AT: 1-800-459-2069

Indicates which employee inspected equip-
ment and on what date.

Indicates that the electrical box on the ma-
chine is in compliance with UL codes.

Electrical maintenance information and sched-
ule provided here.

Do not smoke around machine.  Machine con-
tains a flammable liquid.  Failure to do this
could cause serious injury or death.

Summary of Contents for 4200-D







































Reviews:

No comments