background image

This Krell product has a limited warranty of five years for parts and labor on circuitry from
date of purchase or six years from date of original shipment from the Krell factory. Should
this product fail to perform at any time during the warranty, Krell will repair it at no cost to
the owner, except as set forth in this warranty.

The warranty does not apply to damage caused by acts of God or nature.

The warranty on this page shall be in lieu of any other warranty, expressed or implied,
including, but not limited to, any implied warranty of merchantability or fitness for a 
particular purpose. There are no warranties which exceed beyond those described in this
document. If this product does not perform as warranted herein, the owner’s sole remedy
shall be repair. In no event will Krell be liable for incidental or consequential damages 
arising from purchase, use, or inability to use this product, even if Krell has been advised of
the possibility of such damages.

Proof of purchase in the form of a bill of sale or receipted invoice substantiating that the unit
is within the warranty period must be presented to obtain warranty service. The warranty
begins on the date of retail purchase, as noted on the bill of sale or receipted invoice from
an authorized Krell dealer or distributor.

The warranty for Krell products is valid only in the country to which they were originally
shipped, through the authorized Krell distributor for that country, and at the factory. There
may be restrictions on or changes to Krell’s warranty because of regulations within a 
specific country. Please check with your distributor for a complete understanding of the 
warranty in your country.

If a unit is serviced by a distributor who did not import the unit, there may be a charge for
service, even if the product is within the warranty period.

Freight to the factory is your responsibility. Return freight within the United States (U.S.A.) is
included in the warranty. If you have purchased your Krell product outside the U.S.A. and
wish to have it serviced at the factory, all freight and associated charges to the factory are
your responsibility.

Krell will pay return freight to the U.S.A.-based freight forwarder of your choice. Freight and
other charges to ship the unit from the freight forwarder to you are also your responsibility.

Krell is not responsible for any damage incurred in transit. Krell will file claims for damages
as necessary for units damaged in transit to the factory. You are responsible for filing claims
for shipping damages during the return shipment.

Krell does not supply replacement parts and/or products to the owner of the unit.
Replacement parts and/or products will be furnished only to the distributor performing 
service on this unit on an exchange basis only; any parts and/or products returned to Krell
for exchange become the property of Krell.

No expressed or implied warranty is made for any Krell product damaged by accident,
abuse, misuse, natural or personal disaster, or unauthorized modification.

Any unauthorized voltage conversion, disassembly, component replacement, perforation of
chassis, updates, or modifications performed to the unit will void the warranty.

The operating voltage of this unit is determined by the factory and can only be changed by
an authorized Krell distributor or at the factory. The voltage for this product in the U.S.A.
cannot be changed until six months from the original purchase date.

In the event that Krell receives a product for warranty service that has been modified in any
way without Krell authorization, all warranties on that product will be void. The product will
be returned to original factory layout specifications at the owner’s expense before it is
repaired. All repairs required after the product has been returned to original factory specifi-
cations will be charged to the customer, at current parts and labor rates.

All operational features, functions, and specifications and policies are subject to change
without notification.

Warranty

To register your product 
for warranty benefits,
please complete and return
the Warranty Registration
Card enclosed in the ship-
ping box within 15 days of
purchase. Thank you.

13

Krell S-150m

Summary of Contents for S-150m

















Reviews: