Krell Industries PHANTOM II Owner'S Reference Manual Download Page 3

Page: 3 / 49

Contents

List of Illustrations, page 4

A Letter from Krell Industires LLC, page 5

SECTION ONE: Phantom II Features and Technology, page 6

Features, Revolutionary Krell CAST Technology,

Definition of Terms

SECTION TWO: Unpacking and Placement, page 11

Opening the Phantom II Shipping Carton

SECTION THREE: Quick Start, page 13

Connecting the Phantom II to Your System,

Operating the Phantom II

SECTION FOUR: Anatomy of the Phantom II, page 15

Front Panel Description, Remote Control Description,

Battery Installation, and Back Panel Description

SECTION FIVE: Connecting the Phantom II to Your System, page 26

Input and Output Connections, Connection Steps

SECTION SIX: Phantom II Operation, page 28

On/Off and Stand-by Operation

SECTION SEVEN: Customizing the Phantom II, page 29

Navigation Conventions, Menu Functions

SECTION EIGHT: Troubleshooting System Noise, page 43

WARRANTY, page 44

RETURN AUTHORIZATION PROCEDURE, page 46

SPECIFICATIONS, page 47

Summary of Contents for PHANTOM II


















































Search results

Summary of Contents for PHANTOM II

Reviews:

Related manuals for PHANTOM II

Brands by name

Popular brands

Krell Industries PHANTOM II, Owner'S Reference Manual

Search results

Summary of Contents for PHANTOM II

Reviews:

Related manuals for PHANTOM II

Brands by name

Popular brands