Kreg PRS3034 Installation Instructions Manual Download Page 6

Rabbeted opening method

1. 

Attach the router base to the insert plate, using the screws that 

were used to attach the sub-base to the router base. Depending 
on the thickness of your router sub-base, it may be necessary to 
purchase longer screws. Make certain that the screws are long 
enough to fully thread into the router base. For 

fi

 xed-base routers, 

install the motor unit in the router base and install the insert plate, 
with router attached, in the table. 

2. 

Drop the four lock-down screws through the countersunk holes in 

the insert plate and thread them into the hex nut, wing nut or T-nut. 
Tighten the screws.

Kreg Precision Router Table Insert Plate Levelers method

1. 

With the table top upside down, position an insert-plate leveler 

in one corner of the table-top opening, mating the curve on the 
raised portion of the leveler with the radius corner of the opening. 
Firmly holding the leveler in place and using the three mounting 
holes in the leveler 

fl

 ange as guides, drill pilot holes into the table 

top. Fasten the leveler to the tabletop with three 1¼" coarse-thread 
screws provided 

[Drawing J]

. Repeat with the remaining levelers.

Note:

 The 1¼" coarse-thread screws provided with the levelers 

are for use on router table tops with a minimum thickness of 1". For 
thinner tops, use your own shorter screws.

2. 

Using the 

" hex wrench, drive a ¼-20 x 1½" socket-head set 

screw into each outside hole in each leveler, threading them in 
from the bottom until the tips are 

" below the table surface.

3. 

For Kreg PRS3034 and PRS3036 Precision Insert Plates, fasten 

the router base to the insert plate using the screws supplied with 
the plate. For the Kreg PRS3038 Precision Insert Plate, use the 
screws that were used to attach the sub-base to the router base 
to attach the router base to the insert plate. Make certain that the 
screws are long enough to fully thread into the router base. It may 
be necessary to purchase longer screws. For 

fi

 xed-base routers, 

install the motor unit in the router base.

Precision Insert Plate Installation

5.

Router table top

Mating Curves

Install the Insert Plate

J

Summary of Contents for PRS3034

























Reviews: