Kramer VS-88UHD User Manual Download

Page: 51 / 78

Kramer Electronics Ltd.

VS-88UHD – Technical Specifications

Technical Specifications

Inputs

8 HDMI

On female HDMI connectors

Outputs

8 HDMI

On female HDMI connectors

Ports

1 USB

On a female USB-A connector

1 RS-232

On a 3-pin terminal block for serial link

extension

1 Ethernet

On an RJ-45 female connector for device

control

1 USB

On a female USB-A connector for powering

another device

Video

Max. Resolution

4K@60Hz (4:2:0) and 4K@30Hz (4:4:4)

Compliance

Supports HDMI 1.4 and HDCP 1.4

Control

Front Panel

Front panel buttons

7-segment display

Power

Consumption

50VA

Source

100-240V AC, 50/60Hz

Regulatory Compliance Safety

CE, UL

Environmental

RoHs, WEEE

Environmental

Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RH non-condensing

General

Net Dimensions (W, D, H)

19", 9.3", 1U, rack mountable

Shipping Dimensions (W, D, H)

52.5cm x 33cm x 10.7cm

(20.7” x 13” x 4.2”)

Net Weight

2.6kg (5.73lbs) approx.

Shipping Weight

3.6 kg (7.9lbs) approx.

Accessories

Included

Rack ears, power cord

Specifications are subject to change without notice at

www.kramerav.com

Default Communication Parameters

RS-232/Ethernet

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII Protocol 3000

Stop Bits:

Example (Route input 1 to output 1):

#VID1> 1<cr>

Ethernet Parameters

IP Address:

192.168.1.39

Default TCP Port #:

5000

Subnet Mask:

255.255.0.0

Default UDP Port #:

50000

Default Gateway:

192.168.0.1

Number of TCP ports:

Number of web clients:

Full Factory Reset

Front Panel Buttons:

Power off the device, press and hold the LOCK, EDID and STO buttons simultaneously for

about 3 seconds while powering the device, and then release. Until all front panel buttons

illuminate

Protocol 3000:

“#

factory” command.

Web Pages:

In the Device Settings page, click Reset.

Проконсультироваться

купить

данное

оборудование

вы

можете

компании

АНД

Системс

адрес

: 125480,

Москва

ул

Туристская

.33/1; site: https://andpro.ru

тел

: +7 (495) 545-4870 email: [email protected]

При

обращении

используйте

промокод

AND-PDF

получите

скидку

Summary of Contents for VS-88UHD















































































Search results

Summary of Contents for VS-88UHD

Reviews:

Related manuals for VS-88UHD

Brands by name

Popular brands

Kramer VS-88UHD, User Manual

Search results

Summary of Contents for VS-88UHD

Reviews:

Related manuals for VS-88UHD

Brands by name

Popular brands