Kramer VS-88UHD User Manual Download

Page: 35 / 78

Kramer Electronics Ltd.

VS-88UHD – Using the Embedded Web Pages

Changing Device Settings and Upgrading the Firmware

The Device Settings Web page shows the device details, such as name, MAC address and
firmware version and also enables performing the following functions:



Changing the Ethernet Settings

on page



Performing a Factory Reset

on page



Performing Firmware Upgrade

on page

Changing the Ethernet Settings

To change the Ethernet settings:

1. In the Navigation pane, click

Device Settings

. The Device Settings page appears:

Figure 26: Device Settings Page

2. Uncheck/check the

DHCP

check box.

3. If DHCP is unchecked, change any of the parameters (IP Address, Netmask and/or

Gateway).

4 . Click

Save Changes

Note that:



After changing the IP number, reload the Web page with the new IP address.



After changing the Subnet mask you need to turn the

VS-88UHD

power off and then on

again.



If DHCP is checked, reload the Web page with the new IP address.

Проконсультироваться

купить

данное

оборудование

вы

можете

компании

АНД

Системс

адрес

: 125480,

Москва

ул

Туристская

.33/1; site: https://andpro.ru

тел

: +7 (495) 545-4870 email: [email protected]

При

обращении

используйте

промокод

AND-PDF

получите

скидку

Summary of Contents for VS-88UHD















































































Search results

Summary of Contents for VS-88UHD

Reviews:

Related manuals for VS-88UHD

Brands by name

Popular brands

Kramer VS-88UHD, User Manual

Search results

Summary of Contents for VS-88UHD

Reviews:

Related manuals for VS-88UHD

Brands by name

Popular brands